xinsheng zhang

Dr. xinsheng zhang


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 November 2025 in ACS Omega
Verified
Journal Article
Open access
HLHaixiao Lin
Haixiao Lin
WZWenying Zhang
Wenying Zhang
SGShuaifang Guo
Shuaifang Guo
XZxinsheng zhang
xinsheng zhang
LWLi Wang
Li Wang
JZJiyun Zhang
Jiyun Zhang
The damage to coal-rock masses induced by mining disturbance cannot be overlooked, and the damage deformation characteristics under dynamic loading urgently require investigation. Therefore, this study employs Split Hopkinson Pressure Bar (SHPB) impact tests to reveal the energy evolution mechanism and fractal characteristics of coal failure under dynamic loading. Research indicates that coal deformation exhibits significant strain rate dependence, with both dynamic strength and energy consumption parameters increasing linearly with strain rate. Energy evolution drives crack development through four stages: no damage, microcrack initiation, macroscopic nucleation, and collapse, where the energy consumption required for crack formation exceeds that for crack propagation throughout the entire development process. The fractal dimension of fragmented coal satisfies a positive correlation with both strain rate and fragmentation energy density. Coal possesses favorable self-similarity, and under this condition, increased strain rate enhances the coal’s ability to resist impact through elevated elastic energy density, thereby further strengthening dynamic strength. This confirms intensified fragmentation degree and refined fragment particle size under high energy consumption conditions, providing theoretical support for the prevention and control of mine dynamic disasters.

22 January 2025 in Fractal and Fractional
Verified
Journal Article
Open access
PDF file
DZDan Zhou
Dan Zhou
ZLZhiqiang Lv
Zhiqiang Lv
YCYunxing Cao
Yunxing Cao
Gaofeng LiuGaofeng Liu
Gaofeng Liu
XZxinsheng zhang
xinsheng zhang
SLShimin Liu
Shimin Liu
The pore structure and connectivity of coal are the primary factors influencing the permeability of coal reservoirs. However, clay and carbonate minerals are commonly found filling the pores and fractures within coal. To address the impact of these minerals on fracturing effectiveness, acidic fracturing technology has been introduced. This technique has proven to be an effective measure for enhancing the extraction rate of low-permeability coal seams with high mineral content. In this study, coal samples were treated with a 3% HCl solution, and the changes in the pore structure of the coal before and after acidification were analyzed through low-temperature nitrogen adsorption and X-ray diffraction (XRD) testing. The results were as follows: After acidification, the specific surface area, total pore volume, pore volume in different stages, and average pore size of the coal samples all significantly increased. Specifically, the BET specific surface area grew by an average of 4.8 times and the total pore volume expanded by an average of 7.7 times, with the pore volumes in the pore size ranges of <10 nm and 10–60 nm increasing by an average of 10.1 times and 7.7 times. The smoothness of the pore surface and connectivity of the pore structure in the coal samples improved, as indicated by decreased fractal dimensions D1 (reflecting pore surface roughness) and D2 (representing pore size distribution uniformity). The acidification mechanism was mainly attributed to the dissolution of carbonate minerals in the coal, which led to the removal of obstructive minerals such as ankerite and calcite that had accumulated in the coal pores. This resulted in the formation of new micropores and microfractures, achieving pore volume enhancement and pore expansion.

18 May 2024 in ACS Omega
Verified
Journal Article
Open access
BYBaige Yang
Baige Yang
YCYunxing Cao
Yunxing Cao
XZxinsheng zhang
xinsheng zhang
JZJunsheng Zhang
Junsheng Zhang
SGShuaifang Guo
Shuaifang Guo
Considering the alarming frequency of coal mine gas disasters globally, there is an urgent need to develop efficient gas control technologies to ensure mining safety. This study focuses on the problem of high peak gas emission restriction in the process of coal roadway tunneling in outburst coal seams, taking the No. 15 outburst coal seam of the Pingshu Coal Mine as the research object. Based on coal sample testing analysis and the application of CO2 gas fracturing (CO2-Frac) in coal mines, a comprehensive evaluation was conducted on pore-fracture structure alteration and homogenization gas emission effect induced by CO2-Frac, providing technical solutions for coal mine safety production. The results are as follows: (1) CO2-Frac induces fracture propagation and the development of three types of fracture structures: Tri-Wing Fracture, Damage Markers, and Coal Matrix Fragmentation. (2) Following CO2-Frac at 150 MPa, the pore volume and average diameter of pores in the 100-10,000 nm range increased by 128% and 61%, respectively, compared to the pre-CO2-Frac state. (3) During the excavation period, continuous monitoring of the airflow for 3 days showed a significant homogenization of gas emission, with a maximum value of 0.450% and a variance value of 0.0031, indicating a reduction of 31% and 68%, respectively. These results reveal several key findings: The pore-fracture structure alteration enhances gas diffusion and permeation, providing high-speed pathways for gas migration, resulting in a substantial increase in gas extraction efficiency. During coal cutting, the modified coal exhibits homogenized gas emission, eliminating the high peak phenomenon and achieving safe and efficient mining. These findings demonstrate that CO2-Frac has broad potential in gas emission homogenization for widespread application in coal mines with similar gas geological conditions.

9 May 2025 in ACS Omega
Verified
Journal Article
Open access
BMBingbing Meng
Bingbing Meng
YCYunxing Cao
Yunxing Cao
XZxinsheng zhang
xinsheng zhang
LCLu Chang
Lu Chang
JZJunsheng Zhang
Junsheng Zhang
ZMZiyue Ma
Ziyue Ma
In this study, experiments were conducted to investigate the electric explosion initiation of composite energetic materials (CEMs) by using Cu and NiCr wires in water. The composite energetic material is composed of Al powder and a heater, and there are three formulations after mixing according to the mass ratio (1:1, 1:2, and 1:4). Metal wires with a diameter of 0.5 mm and CEMs were placed inside plexiglass tubes, and two water pressure sensors were arranged at a distance of 50 cm from the wire ignition center; the pulse wave peak pressure and impulse were employed as the parameters for the energy output. Finally, rock fracturing experiments and their mechanical principle analysis were carried out. The results indicate that, compared to a single metal wire electric explosion, it can ignite CEMs to form larger pulse wave energy, and the peak pressure is increased by 3.2 times; the pulse wave peak pressure formed by Cu wire ignition of the CEMs was slightly higher than using NiCr wire under the same conditions, but the impulse generated is the opposite. As the Al powder in the CEMs decreases, the peak pressure gradually increases, which is related to the chemical reactions inside the CEMs. In the experiment of fracturing rocks, water jet and strong light radiation phenomena were discovered, and a complex crack network was formed; the cracks near the pulse center were mainly caused by compressive shear stress, while the cracks in the middle and far parts were mainly formed by radial tensile stress and water wedge action. Finally, with the help of high-speed photography technology, the mechanism by which metal wire electric explosions ignite CEMs in water has been clarified; the combined effects of the shock wave, thermal effect, and light emission generated by the electric explosion of the metal wire drove the release of chemical energy from the CEMs, which is of great significance for the development of this technology.

7 September 2024 in Processes
Verified
Journal Article
Open access
PDF file
ZXZongwei Xu
Zongwei Xu
JZJunsheng Zhang
Junsheng Zhang
YCYunxing Cao
Yunxing Cao
Zhenzhi WangZhenzhi Wang
Zhenzhi Wang
XZxinsheng zhang
xinsheng zhang
The No. 3 coal seam in the Yuxi Coal Mine has a measured maximum gas content of 25.59 m3/t, along with a maximum gas pressure of 2.9 MPa, indicating its high risk to gas and outbursts. To mitigate outburst risks of the coal seam, the 1301 working face has been implemented with gas pre-drainage measures by grid boreholes from underlying roadways. After one year of extraction, it was confirmed that the gas content at all 33 test sites was below 8 m3/t, meeting the outburst prevention standards. However, during subsequent coal tunnel excavation, the gas desorption index K1 value frequently exceeded the standard, resulting in numerous occurrences of abnormal gas emission or small-scale outbursts. To tackle the challenges associated with safe excavation following the first-round regional outburst prevention measures, a research and industrial trial of CO2 gas fracturing (CO2-Frac) technology for secondary outburst prevention and rapid excavation was completed. The results show that the dual-hole and high-pressure (185 MPa) CO2-Frac considerably contributes to outburst prevention. K1 exceedances per hundred meters of tunnel excavations were from an average of 2.54 without CO2-Frac to an average of 0.28 after the new technology was implemented, leading to an eight-fold reduction. Additionally, the monthly excavation footage increased from an average of 81.64 m without CO2-Frac to an average of 162.42 m with CO2-Frac, resulting in a two-fold improvement. The dual-hole and high-pressure CO2-Frac is an advanced technology for safe and efficient excavation for secondary outburst elimination in highly outburst-prone coal seams in the Yuxi Coal Mine, with potential for widespread application in similar coal seam conditions.

4 December 2023 in Water
Verified
Journal Article
Open access
PDF file
SGShuaifang Guo
Shuaifang Guo
YCYunxing Cao
Yunxing Cao
LWLi Wang
Li Wang
XZxinsheng zhang
xinsheng zhang
WZWenying Zhang
Wenying Zhang
BMBingbing Meng
Bingbing Meng
Confining stress response is considered an accompanying behavior of hydraulic fracturing. Along these lines, an evaluation model of confining stress response was presented in this work. It was established on a rock representative volume element (RVE) and based on the hydraulic volumetric opening model, which stems from the theories of poroelasticity, breakdown damage, and hydraulic fracture mechanics. From the extracted outcomes, it was demonstrated that the confinement of the stress response depends on the matching among the characteristic parameters (εb,εs,m) of the rock breakdown, the volumetric opening, and channel flow regimes of the fracturing fluid. Examples in four limiting fracturing regimes show that (1) the confinement of the stress response is strongly determined by the existence of various fracturing regimes and takes place in a different manner during fracture initiation and opening. More specifically, during fracturing initiation, the ratio of the confining stress response to the far-field stress (Pcmax/σh) is 2.0500 in the M regime, 1.9600 in the M˜ regime, 2.7126 in the K regime, and 1.7448 in the K˜ regime, while when the fracture is opened, these values (PC/σh) are 1.8994, 1.8314, 1.6378, and 1.2846, respectively. (2) The impact of the confined stress response to the fluid pressure is also affected by the fracturing regimes; e.g., in both M and M˜ regimes, the peak confinement stress responses lag behind peak pore pressures, but in the K and K˜ regimes, lag off disappears. (3) The pore volumetric opening (Vpe) leads to an increase in the confining stress response, while the fracture opening (Vpd) leads to a reduction in the confining stress response.