Bingbing Meng

Dr. Bingbing Meng


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 January 2024 in ACS Omega
Verified
Journal Article
Open access
BMBingbing Meng
Bingbing Meng
BSBin Shi
Bin Shi
YCYunxing Cao
Yunxing Cao
LWLi Wang
Li Wang
SLShimin Liu
Shimin Liu
N2-hydraulic compound fracturing (NHCF) is an innovative technology aimed at addressing coalbed methane development challenges in low-permeability, low-pressure coal reservoirs in China. However, limited research has been focused on the evolution of damage zones, pore pressure fields, and fluid pressure characteristics in this context. In this paper, we establish a finite element seepage equation based on the volumetric opening model and construct a finite element model for horizontal well stage fracturing. We used the physical and mechanical parameters specific to coal reservoirs in the Xinjing coal mine. Subsequently, we conducted numerical simulations of N2 fracturing (NF), hydraulic fracturing (HF), and NHCF using ANSYS. The results indicate that the initiation-fracturing pressure of NHCF is lower than that of HF but higher than NF, but the steady-fracturing pressure is higher than HF and NF. Moreover, numerical simulation shows that under the same water injection volume, the total volumetric opening formed by NHCF is about 2 times that of HF, NF is the smallest, and the damage zone and pore pressure field caused by NHCF are the largest. Finally, when comparing the casing pressure curve of NHCF by field test with the fluid pressure curve of wellbore obtained from numerical simulation, we observe a strong correlation; the steady fracturing pressure of NF is about 13 MPa, which is basically consistent with the numerical simulation, and the steady- fracturing pressure of HF after NF is about 27 MPa, which is slightly lower than the 30 MPa in numerical simulation. This is because in the numerical simulation, the reservoir parameters after NF can be inherited to the subsequent HF, which cannot be done in the field test. This study presents a novel method for numerical fluid fracturing simulation, offering a fresh perspective on the subject.

9 May 2025 in ACS Omega
Verified
Journal Article
Open access
BMBingbing Meng
Bingbing Meng
YCYunxing Cao
Yunxing Cao
XZxinsheng zhang
xinsheng zhang
LCLu Chang
Lu Chang
JZJunsheng Zhang
Junsheng Zhang
ZMZiyue Ma
Ziyue Ma
In this study, experiments were conducted to investigate the electric explosion initiation of composite energetic materials (CEMs) by using Cu and NiCr wires in water. The composite energetic material is composed of Al powder and a heater, and there are three formulations after mixing according to the mass ratio (1:1, 1:2, and 1:4). Metal wires with a diameter of 0.5 mm and CEMs were placed inside plexiglass tubes, and two water pressure sensors were arranged at a distance of 50 cm from the wire ignition center; the pulse wave peak pressure and impulse were employed as the parameters for the energy output. Finally, rock fracturing experiments and their mechanical principle analysis were carried out. The results indicate that, compared to a single metal wire electric explosion, it can ignite CEMs to form larger pulse wave energy, and the peak pressure is increased by 3.2 times; the pulse wave peak pressure formed by Cu wire ignition of the CEMs was slightly higher than using NiCr wire under the same conditions, but the impulse generated is the opposite. As the Al powder in the CEMs decreases, the peak pressure gradually increases, which is related to the chemical reactions inside the CEMs. In the experiment of fracturing rocks, water jet and strong light radiation phenomena were discovered, and a complex crack network was formed; the cracks near the pulse center were mainly caused by compressive shear stress, while the cracks in the middle and far parts were mainly formed by radial tensile stress and water wedge action. Finally, with the help of high-speed photography technology, the mechanism by which metal wire electric explosions ignite CEMs in water has been clarified; the combined effects of the shock wave, thermal effect, and light emission generated by the electric explosion of the metal wire drove the release of chemical energy from the CEMs, which is of great significance for the development of this technology.

9 February 2026 in Processes
Verified
Journal Article
Open access
PDF file
ZLZhihong Liu
Zhihong Liu
GYGaowei Yue
Gaowei Yue
HLHaixiao Lin
Haixiao Lin
SGShuai Gao
Shuai Gao
BMBingbing Meng
Bingbing Meng
To investigate the dynamic response and failure mechanism of tempered glass subjected to falling-ball impact, a controlled falling-ball impact experimental platform was established. Strain gauges were arranged at multiple locations on the glass surface to capture the transient strain responses under different impact conditions. Based on the experimental setup, a finite element model of tempered glass was developed using Abaqus to simulate the impact process and stress-wave propagation behavior. The experimental results show that falling-ball impact induces pronounced transient strain responses in tempered glass, with strain amplitudes decreasing as the distance from the impact center increases. The strain responses also exhibit clear vibration attenuation characteristics due to energy dissipation and boundary effects. The numerical simulation results are in good agreement with the experimental strain–time history curves in terms of peak strain, temporal evolution, and attenuation trends, confirming the reliability of the numerical model. Further analysis indicates that stress waves generated at the impact point propagate radially within the glass plate and undergo reflection and superposition at the boundaries, leading to localized stress amplification. When the impact energy exceeds a critical threshold, the induced stress surpasses the strength limit of tempered glass, resulting in structural failure. The findings provide theoretical and experimental support for the impact-resistant design and safety assessment of tempered glass.

4 December 2023 in Water
Verified
Journal Article
Open access
PDF file
SGShuaifang Guo
Shuaifang Guo
YCYunxing Cao
Yunxing Cao
LWLi Wang
Li Wang
XZxinsheng zhang
xinsheng zhang
WZWenying Zhang
Wenying Zhang
BMBingbing Meng
Bingbing Meng
Confining stress response is considered an accompanying behavior of hydraulic fracturing. Along these lines, an evaluation model of confining stress response was presented in this work. It was established on a rock representative volume element (RVE) and based on the hydraulic volumetric opening model, which stems from the theories of poroelasticity, breakdown damage, and hydraulic fracture mechanics. From the extracted outcomes, it was demonstrated that the confinement of the stress response depends on the matching among the characteristic parameters (εb,εs,m) of the rock breakdown, the volumetric opening, and channel flow regimes of the fracturing fluid. Examples in four limiting fracturing regimes show that (1) the confinement of the stress response is strongly determined by the existence of various fracturing regimes and takes place in a different manner during fracture initiation and opening. More specifically, during fracturing initiation, the ratio of the confining stress response to the far-field stress (Pcmax/σh) is 2.0500 in the M regime, 1.9600 in the M˜ regime, 2.7126 in the K regime, and 1.7448 in the K˜ regime, while when the fracture is opened, these values (PC/σh) are 1.8994, 1.8314, 1.6378, and 1.2846, respectively. (2) The impact of the confined stress response to the fluid pressure is also affected by the fracturing regimes; e.g., in both M and M˜ regimes, the peak confinement stress responses lag behind peak pore pressures, but in the K and K˜ regimes, lag off disappears. (3) The pore volumetric opening (Vpe) leads to an increase in the confining stress response, while the fracture opening (Vpd) leads to a reduction in the confining stress response.