Zack McClelland

Dr. Zack McClelland


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 February 2024 in Materials
Verified
Journal Article
Open access
PDF file
ZMZack McClelland
Zack McClelland
KDKyle Dunsford
Kyle Dunsford
MWMalcolm Brady Williams
Malcolm Brady Williams
HPHaley E Petersen
Haley E Petersen
Keivan DavamiKeivan Davami
Keivan Davami
Paul G. AllisonPaul G. Allison
Paul G. Allison
High-entropy alloys (HEAs) are new alloy systems that leverage solid solution strengthening to develop high-strength structural materials. However, HEAs are typically cast alloys, which may suffer from large as-cast grains and entrapped porosity, allowing for opportunities to further refine the microstructure in a non-melting near-net shape solid-state additive manufacturing process, additive friction stir deposition (AFSD). The present research compares the microstructure and mechanical behavior of the as-deposited AFSD Al0.35CoCrFeNi to the cast heat-treated properties to assess its viability for structural applications for the first time. Scanning electron microscopy (SEM) revealed the development of fine particles along the layer interfaces of the deposit. Quasi-static and intermediate-rate compression testing of the deposited material revealed a significant strain-rate sensitivity with a difference in yield strength of ~400 MPa. Overall, the AFSD process greatly reduced the grain size for the Al0.35CoCrFeNi alloy and approximately doubled the strength at both quasi-static and intermediate strain rates.

27 March 2024 in Materials
Verified
Journal Article
Open access
PDF file
LSLucinda Slattery
Lucinda Slattery
ZMZack McClelland
Zack McClelland
SHSamuel T Hess
Samuel T Hess
Parts made through additive manufacturing (AM) often exhibit mechanical anisotropy due to the time-based deposition of material and processing parameters. In polymer material extrusion (MEX), printed parts have weak points at layer interfaces, perpendicular to the direction of deposition. Poly(lactic acid) with chopped carbon fiber was printed on a large-format pellet printer at various extrusion rates with the same tool pathing to measure the fiber alignment with deposition via two methods and relate it to the ultimate tensile strength (UTS). Within a singular printed bead, an X-ray microscopy (XRM) scan was conducted to produce a reconstruction of the internal microstructure and 3D object data on the length and orientation of fibers. From the scan, discrete images were used in an image analysis technique to determine the fiber alignment to deposition without 3D object data on each fiber’s size. Both the object method and the discrete image method showed a negative relationship between the extrusion rate and fiber alignment, with −34.64% and −53.43% alignment per extrusion multiplier, respectively, as the slopes of the linear regression. Tensile testing was conducted to determine the correlation between the fiber alignment and UTS. For all extrusion rates tested, as the extrusion multiplier increased, the percent difference in the UTS decreased, to a minimum of 8.12 ± 14.40%. The use of image analysis for the determination of the fiber alignment provides a possible method for relating the microstructure to the meso-property of AM parts, and the relationship between the microstructure and the properties establishes process–structure–property relationships for large-format AM.

13 October 2023 in Metals
Verified
Journal Article
Open access
PDF file
ZMZack McClelland
Zack McClelland
HPHaley E Petersen
Haley E Petersen
KDKyle Dunsford
Kyle Dunsford
Quasi-static and high-rate tensile experiments were used to examine the strain rate sensitivity of laser-directed energy deposition (L-DED)- and additive friction stir deposition (AFSD)-formed AerMet 100 ultrahigh-strength steel-additive manufactured builds. Electron backscattered diffraction (EBSD) revealed similar as-deposited grain sizes between the two AM processes at approximately 24 μm and 17 μm for the L-DED and AFSD samples, respectively. The strain hardening rate, θ, revealed little change in the overall hardening observed in the L-DED and AFSD materials, with a consistent hardening in the quasi-static samples and three identifiable regions in that of the high-rate tested materials. The L-DED deposited materials displayed average ultimate tensile strength values of 1835 and 2902 MPa for the 0.001 s−1 and 2500 s−1 strain rates, respectively and the AFSD deposited materials displayed ultimate tensile strength values of 1928 and 3080 MPa for the 0.001 s−1 and 2500 s−1 strain rates, respectively. Overall, the strength for both processes displayed a positive strain rate sensitivity, with increases in strength of ~1000 MPa for both processes. Fractography revealed significant solidification voids in the laser DED material and poor layer adhesion in the AFSD material.

1 March 2019 in Advances in Civil Engineering Materials
Verified
Journal Article
Closed access
DSDylan A. Scott
Dylan A. Scott
BSBradford P. Songer
Bradford P. Songer
RMRobert D. Moser
Robert D. Moser
ZMZack McClelland
Zack McClelland
BGBrian H. Green
Brian H. Green
CWCharles Weiss
Charles Weiss
This research focused on improving ultra high-performance concrete (UHPC) toughness through the addition of annealed plain carbon steel fibers and stainless steel fibers that both exhibit increased ductility and strain hardening compared with conventional steel fibers used for concrete reinforcement. Implementing optimized heat treatments and selecting proper alternative alloys can improve the postyield carrying capacity of UHPCs through plastic deformations, phase transformations, and fiber pullout. This research focused on the flexural response and dynamic penetration resistance of a UHPC known as Cor-Tuf with three different steel fiber types: plain carbon steel, stainless steel that can exhibit phase transformation-induced plasticity, and annealed carbon steel with reduced tensile strength but increased ductility and strain hardening. Annealed carbon steel fibers were able to reduce mass loss by 0.8 % for 5-cm-thick dynamic impact panels. By using a phase-transformable stainless steel, the ultimate flexural strength increased from 32.0 to 42.5 MPa (33 % increase) and the postimpact velocity decreased an average of 31.5 m/s for 2.5 and 5-cm-thick dynamic impact panels. Phase transformations (austenitic to martensitic) were quantified in the stainless steel fibers of postyielded UHPC specimens using a vibrating sample magnetometer. Stainless steel fibers sampled from the postyielded tensile face of a flexural beam increased from 75 to 107 emu/g. The results of the study evidence improvements in tensile properties and toughness that can be accomplished by modifying the stress versus strain response of steel fiber reinforcement and including new energy dissipation mechanisms such as phase transformation.

1 August 2026 in e-Journal of Nondestructive Testing
Verified
Journal Article
Open access
PDF file
LSLucinda Slattery
Lucinda Slattery
JWJoelle Westcott
Joelle Westcott
ZMZack McClelland
Zack McClelland
This research investigates the integration of fiber optic (FO) strain sensors into Large Format Additive Manufacturing (LFAM) components to enable real-time structural health monitoring (SHM) for civil infrastructure. The study addresses four fundamental questions: (1) Can embedded fiber optics reliably identify structural events and usage patterns? (2) Is adequate interfacial bonding achieved between the fiber optic sensor and polymer matrix? (3) How does the embedding process affect strain measurement accuracy? (4) What impact does sensor integration have on the mechanical performance of printed components? Twenty short carbon fiber-reinforced PLA specimens were fabricated in two configurations, neat and fiber-optic-embedded, and subjected to quasi-static tensile testing to failure and displacement-controlled cyclic fatigue testing. The embedding process leveraged LFAM’s layer-by-layer deposition and relatively low processing temperatures to place optical fibers between print layers without modifying standard print parameters. X-ray computed tomography revealed a fiber-to-matrix contact percentage of 58.2%, indicating that interfacial porosity introduced during embedding partially limits strain transfer and that absolute FO strain measurements should be interpreted alongside an independent reference measurement. Under cyclic fatigue loading, embedded FO sensors demonstrated strong qualitative agreement with load-cell-reported stress measurements, faithfully resolving cycle peaks, valleys, and transitions in real time. Quantitative differences between FO-measured strain and crosshead-derived applied strain were attributed to the limitations of crosshead displacement as a proxy for material strain, incomplete fiber-matrix contact, and local material heterogeneity. Across both testing regimes, the influence of FO embedment on bulk mechanical performance was inconsistent, with no systematic reduction in peak force or displacement, although inherent variability in the printed material limited definitive conclusions. These results demonstrate that fiber optic sensors can be embedded into LFAM components without meaningful disruption to fabrication or a consistent mechanical penalty, supporting the broader vision of self-sensing structural components with built-in monitoring capabilities. Further development is needed to improve fiber-matrix contact quality and expand the experimental test matrix for practical deployment in civil infrastructure applications.