ARWINDRA RIZQIAWAN

Dr. ARWINDRA RIZQIAWAN

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 January 2021 in Energies
Verified
Journal Article
Open access
PDF file
TATri Ardriani
Tri Ardriani
PDPekik Argo Dahono
Pekik Argo Dahono
ARARWINDRA RIZQIAWAN
ARWINDRA RIZQIAWAN
EGErna Garnia
Erna Garnia
PSPungky Dwi Sastya
Pungky Dwi Sastya
MRMuhammad Ridwan
Muhammad Ridwan
DC microgrid has been gaining popularity as solution as a more efficient and simpler power system especially for remote areas, where the main grid has yet to be built. This paper proposes a DC microgrid system based on renewable energy sources that employs decentralized control and without communication between one grid point and another. It can be deployed as an individual isolated unit or to form an expandable DC microgrid through DC bus for better reliability and efficiency. The key element of the proposed system is the power conditioner system (PCS) that works as an interface between energy sources, storage system, and load. PCS consists of modular power electronics devices and a power management unit, which controls power delivery to the AC load and the grid as well as the storage system charging and discharging sequence. Prototypes with 3 kWp solar PV and 13.8 kWh energy storage were developed and adopt a pole-mounted structure for ease of transportation and installation that are important in remote areas. This paper presents measurement results under several conditions of the developed prototypes. The evaluation shows promising results and a solid basis for electrification in remote areas.

4 October 2023 in Energies
Verified
Journal Article
Open access
PDF file
RARidha D. N. Aditama
Ridha D. N. Aditama
NRNaqita Ramadhani
Naqita Ramadhani
TATri Ardriani
Tri Ardriani
JFJihad Furqani
Jihad Furqani
ARARWINDRA RIZQIAWAN
ARWINDRA RIZQIAWAN
PDPekik Argo Dahono
Pekik Argo Dahono
Raising the electrification ratio to 100% is still a formidable challenge in Indonesia, especially in the remote areas of the eastern part of the archipelago. A DC microgrid system is one of the most viable solutions to increase the electricity supply in remote areas, taking advantage of various renewable energy sources that are located near the rural load centers. A DC–DC power converter for a rural DC microgrid system needs to have a high voltage gain to facilitate the power conversion from low-voltage PV output to a high-voltage DC microgrid bus, a very low input ripple current to help maintain the PV or battery lifetime, and be highly modular for ease of transport and assembly. Many topologies have been proposed to obtain high voltage gain, very low ripple current, and modularity. However, they usually use either bulky and lossy magnetic components, are sensitive to component parameter variance and need special voltage-balancing techniques, or have different component ratings for their multilevel configuration which weakens the modularity aspect. This paper proposes a new modular multilevel DC–DC converter that is very suitable for rural DC microgrid applications based on a modified buck–boost topology. The proposed converter is easily stackable to achieve high voltage gain and does not require any voltage balancing techniques, thus enhancing the modularity characteristics and simplifying its control method. Moreover, the ripple current can be reduced by employing a multiphase configuration. This converter can also facilitate bidirectional power flow to serve as a battery charger/discharger. A comprehensive analysis of voltage gain and ripple current are presented to explain the inner workings of this converter. Finally, the performance of this converter is verified through simulation and experiment, showing the converter’s modularity, bidirectional power capability, and potential to achieve voltage gain and ripple-current requirements of the DC microgrid system.

9 October 2024 in IEEE Access
Verified
Journal Article
Open access
WDWakhyu Dwiono
Wakhyu Dwiono
BTBambang Riyanto Trilaksono
Bambang Riyanto Trilaksono
TRTri Desmana Rachmildha
Tri Desmana Rachmildha
ARARWINDRA RIZQIAWAN
ARWINDRA RIZQIAWAN
Solar energy utilization, in conjunction with battery systems, within stand-alone DC microgrid systems represents a significant trend. In such isolated network configurations, the voltage of the Direct Current (DC) bus experiences fluctuations: it increases when the islanded DC microgrid receives excess energy and decreases during periods of energy scarcity. Ensuring the appropriate operational mode for photovoltaic (PV) panels is crucial for maintaining the DC bus voltage within specified operational limits, which guarantees high electrical quality, whether the power is used to supply loads directly or converted to AC form. Furthermore, achieving balanced power sharing between the PV and the energy storage system enhances the efficiency of the energy storage workload. This study proposes a transition function to facilitate seamless switching of the PV panel’s operational mode between Maximum Power Point Tracking (MPPT) and voltage-controlled modes. This transition function is applied to the PV side converter, which adjusts the duty cycle value of both MPPT and droop mode outputs based on the microgrid’s energy adequacy condition, as determined by the DC bus voltage readings. Moreover, this study introduces a Duty Cycle Range Divider (DCRD) algorithm to derive the converter’s Piece-wise Affine (PWA) model. Subsequently, a linear quadratic regulator (LQR) controller, designed based on the PWA model, is employed alongside the transition function to enhance the DC microgrid’s dynamic performance. A similar LQR controller is applied to the battery-side converter in conjunction with a battery State of Charge (SoC)-based droop control to balance the power-sharing. The proposed control strategy stabilizes the DC bus voltage and ensures a seamless response during transitions in the PV system’s operating mode. The efficacy of this strategy is validated through MATLAB Simulink simulations and laboratory-scale experiments.

1 June 2025 in International Journal of Power Electronics and Drive Systems (IJPEDS)
Verified
Journal Article
Open access
PDF file
ATAdnan Rafi Al Tahtawi
Adnan Rafi Al Tahtawi
ARArief Syaichu Rohman
Arief Syaichu Rohman
PRPranoto Hidaya Rusmin
Pranoto Hidaya Rusmin
ARARWINDRA RIZQIAWAN
ARWINDRA RIZQIAWAN
The addition of a supercapacitor to electric vehicles is considered beneficial for extending battery lifetime. Due to its higher power density compared to the battery, a supercapacitor can efficiently handle sudden high-current demands. However, to achieve energy efficiency, a specific control strategy is required for this battery-supercapacitor (Batt-SC) hybrid power source (HPS). This paper reviews the dynamic model of the Batt-SC as HPS for electric vehicles and explores its various control strategies in order to achieve energy efficiency. A high-fidelity model, a control-oriented model, and an integrated dynamic model are presented. Various control strategies are then discussed, including high-level control, low-level control, and DC bus voltage regulation. This paper also identifies several key research opportunities, such as developing an integrated dynamic model of a hybrid Batt-SC electric vehicle, combining high-level and low-level control into a unified control strategy, and designing an optimal-adaptive controller that can minimize a certain performance index by considering nonlinearity factors.

1 June 2024 in International Journal of Power Electronics and Drive Systems (IJPEDS)
Verified
Journal Article
Open access
PDF file
SWSulistyo Wijanarko
Sulistyo Wijanarko
GHGifari Iswandi Hasyim
Gifari Iswandi Hasyim
JFJihad Furqani
Jihad Furqani
ARARWINDRA RIZQIAWAN
ARWINDRA RIZQIAWAN
PDPekik Argo Dahono
Pekik Argo Dahono
AMAnwar Muqorobin
Anwar Muqorobin
One way to increase electric vehicle (EV) battery utilization is to connect it to a dc microgrid. The EV battery can assume the role of an energy storage from the grid point of view. A bidirectional DC-DC converter will be needed to transfer power between them back and forth. This paper proposes the converter design considering its functional objective, including interleaved phase number determination. Efficiency performance evaluation is presented by power loss analysis with the parasitic-parameters consideration of the components. Finding optimum switching frequency based on power loss analysis is performed independently between input and output sides of the converter. Finally, experiments using a scaled-down prototype are shown to verify the analytical analysis of the converter. The experimental results properly validate the power loss analytic analysis carried out in this paper with a maximum error of 2.04% at 1131-watt, 60 V battery voltage, and 140 V grid voltage. Maximum efficiency 96.97% is obtained at 301-watt, 130 V battery voltage, and 151 V grid voltage. Overall, the converter has a simple structure, capable to be operated in various levels of input and output voltages with a minimum battery side current ripple.

25 December 2024 in e-Prime - Advances in Electrical Engineering, Electronics and Energy
Verified
Journal Article
Open access
ASAgustinus Yudhistira Wicaksono Setyanto
Agustinus Yudhistira Wicaksono Setyanto
ARARWINDRA RIZQIAWAN
ARWINDRA RIZQIAWAN
TATri Ardiani
Tri Ardiani