Germanium tin (GeSn) is a tuneable narrow bandgap material, which has shown remarkable promise for the industry of near- and mid-infrared technologies for high efficiency photodetectors and laser devices. Its synthesis is challenged by the lattice mismatch between the GeSn alloy and the substrate on which it is grown, sensitively affecting its crystalline and optical qualities. In this article, we investigate the growth of Ge and GeSn on GaAs (001) substrates using two different buffer layers consisting of Ge/GaAs and Ge/AlAs via molecular beam epitaxy. The quality of the Ge layers was compared using X-ray diffraction, atomic force microscopy, reflection high-energy electron diffraction, and photoluminescence. The characterization techniques demonstrate high-quality Ge layers, including atomic steps, when grown on either GaAs or AlAs at a growth temperature between 500–600 °C. The photoluminescence from the Ge layers was similar in relative intensity and linewidth to that of bulk Ge. The Ge growth was followed by the growth of GeSn using a Sn composition gradient and substrate gradient approach to achieve GeSn films with 9 to 10% Sn composition. Characterization of the GeSn films also indicates high-quality gradients based on X-ray diffraction, photoluminescence, and energy-dispersive X-ray spectroscopy measurements. Finally, we were able to demonstrate temperature-dependent PL results showing that for the growth on Ge/GaAs buffer, the direct transition has shifted past the indirect transition to a longer wavelength/lower energy suggesting a direct bandgap GeSn material.
We investigated the thermal stability and performance of AlGaN/AlN/GaN Hall-effect sensors under industry-relevant atmospheric conditions. The thermal stability and performance of Hall sensors are evaluated by monitoring Hall sensitivity, two-dimensional electron gas density, and Ohmic contact resistance during aging at 200 °C for up to 2800 h under atmospheric conditions. This was accomplished by characterizing AlGaN/AlN/GaN micro-Hall sensors, with and without contacts, and before and after being placed under different thermal aging times. Observed electrical performance was correlated with the micro-structural evolution of AlGaN/AlN/GaN Hall sensor heterostructures. Results indicate that the AlGaN/AlN/GaN Hall sensor provides stable performance for as long as 2800 h aging at 200 °C without any significant degradation of (i) Hall sensitivity, (ii) two-dimensional electron gas, and (iii) Ohmic contacts. However, there was a small change in sheet density and mobility, which is due to a decrease in polarization, resulting from local inhomogeneous strain relief at the barrier layer. During the early stage of thermal aging, a decrease in contact resistance was also observed and attributed to (i) out-diffusion of “Ga” at the vicinity of the contact interface, and (ii) a reduction in oxygen concentration and formation of Al–Ti intermediate alloy at the GaN/Ti interface, resulting in a reduced barrier and enhanced electron transport at the contacts. However, despite these small changes, results indicate that the AlGaN/AlN/GaN Hall sensor provides stable performance for as long as 2800 h thermal aging at 200 °C.
A study of the mechanism of Sn out-diffusion was performed by annealing Ge0.905Sn0.095 layers at 300 °C. The changes in Sn composition and strain state were confirmed by x-ray diffraction and photoluminescence spectroscopy. Surface defects, appearing as Sn particles, with the highest density of 3.5 × 108 cm−2 were detected by atomic force microscopy after annealing for 2 h. The strain in the GeSn layer stabilized for more prolonged annealing, while the density of particles decreased and their size increased. Annealing results are discussed in terms of Sn segregation and subsequent diffusion along dislocation lines, enhanced out-diffusion by dislocations migration, and surface particle coalescence.
1 July 2024 in Journal of Vacuum Science & Technology B
The development of all-group IV GeSn materials on Si substrates is of interest for monolithic midwave infrared (MWIR) silicon photonics. Despite their great potential, the growth of high crystalline quality materials is still challenging. The conventional growth of GeSn films on Si displays high densities of dislocations and, hence, large dark currents. We have examined a state-of-the-art lithographically defined aspect ratio trapping (ART) growth approach for threading dislocations (TDs) filtering in GeSn and demonstrated the selective growth in the holes embedded in the SiO2/Si(001) template. While an exceptionally low density of TDs was confirmed by transmission electron microscopy imaging, we find that Sn incorporation is strongly suppressed in the ART-grown structures. Nonetheless, these results provide a solid basis for further efforts to enhance the Sn fraction of the GeSn ART growth.
Germanium films were grown on c-plane sapphire with a 10 nm AlAs buffer layer using molecular beam epitaxy. The effects of Ge film thickness on the surface morphology and crystal structure were investigated using ex situ characterization techniques. The nucleation of Ge proceeds by forming (111) oriented three-dimensional islands with two rotational twin domains about the growth axis. The boundaries between the twin grains are the origin of the 0.2% strain and tilt grains. The transition to a single-grain orientation reduces the strain and results in a better-quality Ge buffer. Understanding the role of thickness on material quality during the Ge(111)/Al2O3(0001) epitaxy is vital for achieving device quality when using group IV material on the sapphire platform.