Recent progress in additive manufacturing, also known as 3D printing, has offered several benefits, including high geometrical freedom and the ability to create bioinspired structures with intricate details. Mantis shrimp can scrape the shells of prey molluscs with its hammer-shaped stick, while beetles have highly adapted forewings that are lightweight, tough, and strong. This paper introduces a design approach for bioinspired lattice structures by mimicking the internal microstructures of a beetle’s forewing, a mantis shrimp’s shell, and a mantis shrimp’s dactyl club, with improved mechanical properties. Finite element analysis (FEA) and experimental characterisation of 3D printed polylactic acid (PLA) samples with bioinspired structures were performed to determine their compression and impact properties. The results showed that designing a bioinspired lattice with unit cells parallel to the load direction improved quasi-static compressive performance, among other lattice structures. The gyroid honeycomb lattice design of the insect forewings and mantis shrimp dactyl clubs outperformed the gyroid honeycomb design of the mantis shrimp shell, with improvements in ultimate mechanical strength, Young’s modulus, and drop weight impact. On the other hand, hybrid designs created by merging two different designs reduced bending deformation to control collapse during drop weight impact. This work holds promise for the development of bioinspired lattices employing designs with improved properties, which can have potential implications for lightweight high-performance applications.
Inconel 625 is widely employed in high-temperature and corrosive environments, where the integrity of welded joints critically influences component performance. This study systematically investigates how laser beam welding (LBW) heat input governs cooling behaviour, microstructure evolution, elemental segregation, and the mechanical performance of Inconel 625 weld joints aiming to become sustainable joints. A single-spot monochromatic non-contact type infrared pyrometer is used to monitor the thermal cycles of the molten weld pool and the cooling rate and melt pool lifetime were determined based on the thermal cycle data. The impact of cooling rate and melt pool lifetime on weld geometry, microstructure, micro-segregation, and mechanical properties were thoroughly investigated. The findings revealed that the fibre laser welding produced sound, defect-free joints across all experimental heat-input conditions and the weld quality was fairly dictated by cooling rate during solidification. Reducing heat input (by using faster laser scan speeds) increased the cooling rate (1.45 × 103 to 3.65 × 103 °C/s), resulting in a shortened melt-pool lifetime and altered weld bead geometry from hourglass to truncated-cone profiles. Eventually, the fusion-zone microstructure transitioned from coarse cellular/columnar dendrites at high heat inputs to refined dendrites at low heat inputs. The EDS analysis revealed pronounced Nb and Mo segregation in slowly cooled welds and Laves phase formation due to insufficient time for solute redistribution and γ-Ni matrixes were consistent noted with XRD-observed peaks. The presence of the brittle Laves phase adversely affects the microhardness and tensile strength of the weld joints. Mechanical testing confirmed that decreasing heat input (in faster laser scan speeds) enhanced micro-hardness and tensile strength due to grain refinement and solute entrapment in the γ matrix. The highest joint strength (989.3 ± 10.4 MPa) and elongation (40.3 ± 1.8%) approached those of the work material, and these findings establish processing parameter–structure–property relationships for the LBW of Inconel 625. The co-relation in the present manuscript can be used in the future for process monitoring and for controlling the mechanical properties of laser welding and may provide a practical guidance for optimizing weld quality in advanced industrial applications.
9 March 2026 in International Journal of Metalcasting
Hollow microneedle (HMN) systems can deliver insulin with minimal pain, but most rely on external pumps that add bulk, cost, and failure modes. This paper reports the design, fabrication, and mechanical characterisation of a pump-free, refillable HMN patch that integrates a syringe-loadable, self-sealing reservoir and delivers by passive diffusion. A 3 × 4 array of side-orifice conical HMNs with a target height of 1 mm and a bore of 0.8 mm was stereolithography-printed in dental-grade resin and coupled to an elastic-grade resin septum that maintains a leak-free seal after repeated needle puncture. A surface-response design of experiments (DoE) probed wall thickness of 0.10–0.20 mm, post-cure time of 20–60 min, and temperatures of 35–80 °C. The microneedle characteristics include geometric fidelity, insertion into multilayer Parafilm, and axial compression to 150 N. All patches were printed with a hollow channel and side orifices with tips were slightly blunted. Relative to the original design, height undershoot was from −24.5% to −60.5% while base diameters were within −11% to +20%. Parafilm insertion exhibited a peak then force drop at about 0.22 mm displacement with 1.2–1.5 N pierced the first layer. It was found that about 90% of needles penetrated about 381 µm and more than 20% reached 635 µm. Patches withstood 150 N without fracture with strains of 9.7–15.6% and modulus of 8–48 MPa. ANOVA identified wall thickness as a significant factor, with curing temperature not being significant. Contour analysis defined an operating window near a 0.15 mm wall and about 40 min post-cure balancing dimensional fidelity and post-compression height retention. These results define a manufacturable path to compact, pump-free insulin patches with low insertion force and robust mechanics, opening a clinically scalable route to simpler everyday insulin therapy.
Imidacloprid (IMI), the commonly used neonicotinoid pesticide, has emerged as a persistent aquatic contaminant due to its high solubility and stability, posing risks to non-target organisms and ecosystem health. In this study, a MnZnFe2O4/SrWO4 ferrite–tungstate nanocomposite was synthesized via a hydrothermal process and its ability to photocatalytically degrade IMI under UV light was assessed. SEM, XRD and FT-IR were used to characterize the composite to confirm its structural and morphological features. Photocatalytic performance was systematically investigated by examining the effects of operational factors, including initial pollutant concentration, catalyst dosage, pH, and irradiation time. The MnZnFe2O4/SrWO4 nanocomposite exhibited significantly enhanced activity, achieving up to 87% degradation of IMI within 30 min at pH 9, outperforming individual components (SrWO4: 37%; MnZnFe2O4: 75%) under identical conditions. The degradation kinetics followed a pseudo-first-order model consistent with the Langmuir–Hinshelwood mechanism. Effective interfacial charge transfer between the ferrite and tungstate phases, which suppresses electron-hole recombination and increases the production of reactive species, is responsible for the enhanced performance. Furthermore, the composite demonstrated good stability and reusability across several cycles, indicating its practical applicability. Overall, the results demonstrate the potential of MnZnFe2O4/SrWO4 nanocomposites as efficient and sustainable photocatalysts for removing imidacloprid and similar organic contaminants from aqueous systems.
One of the most important assumptions in production scheduling is that the machines are permanently available without any breakdown. In the real world of scheduling, machines can be made unavailable due to various reasons such as preventive maintenance and unpredicted breakdown. In this research, the production scheduling is explored and we considered the machine consists of some components or elements each is subjected to failure rate with different scale and shape parameters. The machine components are under the competing risk reliability model as an availability constraint. A well known enumeration solution technique is designed for the small size problems then an evolutionary metaheuristic based on genetic algorithm is designed for larger problems. The results showed a great chance to enhance the scheduling problem through modifying some basic assumptions.