Recent progress in additive manufacturing, also known as 3D printing, has offered several benefits, including high geometrical freedom and the ability to create bioinspired structures with intricate details. Mantis shrimp can scrape the shells of prey molluscs with its hammer-shaped stick, while beetles have highly adapted forewings that are lightweight, tough, and strong. This paper introduces a design approach for bioinspired lattice structures by mimicking the internal microstructures of a beetle’s forewing, a mantis shrimp’s shell, and a mantis shrimp’s dactyl club, with improved mechanical properties. Finite element analysis (FEA) and experimental characterisation of 3D printed polylactic acid (PLA) samples with bioinspired structures were performed to determine their compression and impact properties. The results showed that designing a bioinspired lattice with unit cells parallel to the load direction improved quasi-static compressive performance, among other lattice structures. The gyroid honeycomb lattice design of the insect forewings and mantis shrimp dactyl clubs outperformed the gyroid honeycomb design of the mantis shrimp shell, with improvements in ultimate mechanical strength, Young’s modulus, and drop weight impact. On the other hand, hybrid designs created by merging two different designs reduced bending deformation to control collapse during drop weight impact. This work holds promise for the development of bioinspired lattices employing designs with improved properties, which can have potential implications for lightweight high-performance applications.
Single-point incremental forming (SPIF) is a flexible technology that can form a wide range of sheet metal products without the need for using punch and die sets. As a relatively cheap and die-less process, this technology is preferable for small and medium customised production. However, the SPIF technology has drawbacks, such as the geometrical inaccuracy and the thickness uniformity of the shaped part. This research aims to optimise the formed part geometric accuracy and reduce the processing time of a two-stage forming strategy of SPIF. Finite element analysis (FEA) was initially used and validated using experimental literature data. Furthermore, the design of experiments (DoE) statistical approach was used to optimise the proposed two-stage SPIF technique. The mass scaling technique was applied during the finite element analysis to minimise the computational time. The results showed that the step size during forming stage two significantly affected the geometrical accuracy of the part, whereas the forming depth during stage one was insignificant to the part quality. It was also revealed that the geometrical improvement had taken place along the base and the wall regions. However, the areas near the clamp system showed minor improvements. The optimised two-stage strategy successfully decreased both the geometrical inaccuracy and processing time. After optimisation, the average values of the geometrical deviation and forming time were reduced by 25% and 55.56%, respectively.
Auxetic lattice structures are three-dimensionally designed intricately repeating units with multifunctionality in three-dimensional space, especially with the emergence of additive manufacturing (AM) technologies. In aerospace applications, these structures have potential for use in high-performance lightweight components, contributing to enhanced efficiency. This paper investigates the design, numerical simulation, manufacturing, and testing of three-dimensional (3D) star-shaped lattice structures with tailored mechanical properties. Finite element analysis (FEA) was employed to examine the effect of a lattice unit’s vertex angle and strut diameter on the lattice structure’s Poisson’s ratio and effective elastic modulus. The strut diameter was altered from 0.2 to 1 mm, while the star-shaped vertex angle was adjusted from 15 to 90 degrees. Laser powder bed fusion (LPBF), an AM technique, was employed to experimentally fabricate 3D star-shaped honeycomb structures made of Ti6Al4V alloy, which were then subjected to compression testing to verify the modelling results. The effective elastic modulus was shown to decrease when increasing the vertex angle or decreasing the strut diameter, while the Poisson’s ratio had a complex behaviour depending on the geometrical characteristics of the structure. By tailoring the unit vertex angle and strut diameter, the printed structures exhibited negative, zero, and positive Poisson’s ratios, making them applicable across a wide range of aerospace components such as impact absorption systems, aircraft wings, fuselage sections, landing gear, and engine mounts. This optimization will support the growing demand for lightweight structures across the aerospace sector.
Metal-based ceramic composite laser cladding offers substantial compensations in enhancing brake disc surface characteristics. Laser cladding was utilized to combine B4C powder (10–40%) with Ni 63 powder to make Boron Carbide (B4C)/Nickel 63 composite coatings. For the subsequent experiments, the specimens were ground and polished. Bonding strength, fracture toughness, and residual stress were examined with the B4C content. The fracture morphologies were checked using a scanning electron microscope (SEM). It was observed that the bonding strength of various coatings might approach 175 MPa. Best bonding was observed when the B4C level was between 15% and 30%. The porousness of the coating continuously raised as B4C content increased. The coating’s maximum permeability was 5.6% after the B4C level reached 30%. As the B4C level in the coating grew, the coating’s compression resistance decreased. The bonding strength was within desirable limits, and compression resistance was consistently strong. The material bending strength increased when the B4C materials were reduced below 35%; at this level, the bending strength was highest. The bending strength was covered by the optimal range of bonding strength. Good bonding strength and mechanical characteristics were achieved when B4C content was 20% to 30%. The 20% B4C coating had the smoothest fracture morphologies and the strongest bonding strength, making it the most stable. For the estimation of total matrix deformation and corresponding coating stress on coated brake discs, Ansys software was utilized to create a static structural model.
The wear surface morphology of AlSi10Mg specimens, originally manufactured using selective laser melting (SLM), has been analyzed in the context of exposure to heat from gas flames. The first stage of the experimental work included the performance of surface heat-exposure on SLM-prepared specimens through oxyacetylene gas welding. Gas welding was utilized with three different flames, namely; reducing, neutral, and oxidizing on the as-built specimens of SLM. The post-surface-treated specimens were subjected to pin-on-disk wear testing against fixed parameters. After the performance of wear testing at two different radii, the mass loss of each of the four types of specimens was calculated including the three specimens exposed to heat along with the as-built specimens. The results showed that the maximum amount of mass losses at 24 mm and 30 mm radii belongs to the neutral flame specimens and the least was for the as-built condition specimens. Upon analysis, the heat-exposure specimens through all three types of gas flames resulted in an increase in the amount of mass in contrast to the as-built specimens. Moreover, the morphologies of the developed wear tracks at surfaces were examined using the scanning electron microscope (SEM) for the understating of the mechanism.
This paper presents an experimental investigation of the fabrication of Cu–multi-walled carbon nanotube (MWCNT) nanocomposites prepared via the electroless chemical deposition technique followed by the powder metallurgy (PM) method. To enhance the dispersion and wettability of MWCNTs with a Cu matrix, MWCNTs were given an electroless coating of Ag nanoparticles. MWCNTs with 0.4, 0.8, and 1.2 wt.% were first coated with 5 wt.% Ag nanoparticles, then mechanically milled with Cu nanoparticles using a 10:1 ball-to-powder ratio for 60 min at 300 rpm. The mixed samples (35 g) were subjected to a compression pressure of 700 MPa and sintered at 950 °C in a hydrogen-inert gas furnace. Mapping and microstructure analyses were conducted to analyze the constituents’ homogeneity. In addition, the electrochemical properties and corrosion resistance of specimens were investigated. The results revealed that the relative density decreased by raising the MWCNTs’ content. Electrical resistivity increased gradually with the addition of MWCNTs coated by Ag nanoparticles, and the thermal conductivity decreased. It was also revealed that the smallest corrosion rate could be obtained for the sample with 1.2 wt.% MWCNTs, which is the appropriate rate for the electrochemical deposition.