Currently, the automotive market is undergoing a vibrant transition toward component electrification driven by the widespread adoption of electric vehicles. The steering system, electric power steering (EPS), has evolved gradually from traditional hydraulic systems (HPSs) to electric systems. The current state sees the majority of commercial vehicles equipped with electric EPS systems. EPS reduces the steering effort applied to the steering wheel during low-speed driving, enhancing driving convenience. It is widely adopted in most commercial vehicles due to numerous advantages such as system simplification, speed-dependent steering control, and vehicle weight reduction compared to traditional HPSs. EPS can achieve a 3%–5% improvement in fuel efficiency compared to traditional HPSs because it operates only when the driver manipulates the steering wheel. However, what matters most in EPS is vibration and noise. Drivers are directly exposed to the vibration and noise of EPS. Therefore, it is crucial to implement electromagnetic designs that reduce cogging torque and torque ripple, which are the causes of vibrations and noise in electric motors. However, due to the inherent characteristics of electric motors, in structures designed for winding coil windings, such as fixed stator slots and teeth, the variation in reluctance during operation is not consistent. Consequently, this leads to an increase in the occurrence of cogging torque and torque ripple. However, if an EPS motor is designed with a structure lacking stator teeth, the change in reluctance during rotor rotation remains constant. In theory, this would significantly reduce cogging torque and torque ripple when the rotor is in motion. Therefore, in this article, the conventional EPS motor, designed with a structure containing stator teeth resulting in cogging torque and torque ripple, is targeted for reduction. This article designed a slotless motor structure with the goal of significantly minimizing these effects. In this article, pursued a design to achieve the target output of the EPS slotless motor and enhance the overall output density. Ultimately, this motor designed, fabricated, and analyzed a motor for the automotive EPS system with the capability to reduce vibrations and noise while achieving weight reduction.

A PCB stator axial flux permanent magnet (AFPM) motor is presented that overcomes the manufacturing challenges associated with the complex geometry of conventional stators by employing a PCB substrate. Traditionally, AFPM motors are produced by winding coils around the stator teeth, a process that requires specialized winding machinery and is both labor intensive and time consuming, ultimately incurring considerable manufacturing costs and delays. In contrast, PCB substrates offer significant advantages in manufacturability and mass production, effectively resolving these issues. Furthermore, the primary material used in PCB substrates, FR-4, exhibits a permeability similar to that of air, resulting in negligible electromagnetic cogging torque. Cogging torque arises from the attraction between permanent magnets and stator teeth, creating forces that interfere with motor rotation and generate unwanted vibration, noise, and potential mechanical collisions between the rotor and stator. In the PCB stator design, the conventional PCB circuit pattern is replaced by the motor’s coil configuration, and the absence of stator teeth eliminates these interference issues. Consequently, a slotless motor configuration with minimal vibration and noise is achieved. The PCB AFPM motor has been applied to a vehicle-mounted electric water pump (EWP), where mass production and space efficiency are critical. In an EWP, which integrates the impeller with the motor, it is essential that vibrations are minimized since excessive vibration could compromise impeller operation and, due to fluid resistance, require high power input. Moreover, the AFPM configuration facilitates higher torque generation compared to a conventional radial flux permanent magnet synchronous motor (RFPM). In a slotless AFPM motor, the absence of stator teeth prevents core flux saturation, thereby further enhancing torque performance. AC losses occur in the conductors as a result of the magnetic flux produced by the permanent magnets, and similar losses arise within the PCB circuits. Therefore, an optimized PCB circuit design is essential to reduce these losses. The Constant Trace Conductor (CTC) PCB circuit design process is proposed as a viable solution to mitigate AC losses. A 3D finite element analysis (3D FEA) model was developed, analyzed, fabricated, and validated to verify the proposed solution.

This paper proposes a design method to reduce cogging torque and torque ripple in the concentrated winding of IPMSMs (Interior Permanent Magnet Synchronous Motors) used in motors for the semiconductor ETCH process. IPMSMs can utilize reluctance torque through the difference in inductance between the d axis and q axis, but they are at a disadvantage in terms of reducing cogging torque while tapering the rotor and stator to reduce torque ripple. In addition, the existing single tapering can push the permanent magnets into the rotor. If the rotor’s permanent magnets are embedded, the magnetic reluctance will increase, and the overall performance of the motor will decrease. However, an optimum design method was derived in which the magnets do not move during rotor tapering. This geometric design is an optimum design method that reduces cogging torque and torque ripple. This paper compares and analyzes four models, the concentrated winding model, distributed winding model, conventional tapering model, and separated tapering model, using 2D and 3D finite element analysis (FEA).

Surface permanent-magnet synchronous motors (SPMSMs) have been widely adopted for ship propulsion due to their high power density and efficiency. However, conventional three-phase open-slot SPMSMs struggle to balance high efficiency with reductions in cogging torque and torque ripple. This paper proposes a design of an SPMSM with a six-phase winding configuration and a chamfer-shaped permanent magnet to reduce cogging torque and torque ripple. Electromagnetic performance is evaluated through finite element analysis (FEA). A reference three-phase interior PMSM and three-phase SPMSMs with different magnet shapes are first compared to identify a suitable basic design. Based on the basic machine, three pole–slot combinations for the six-phase winding are analyzed, and the most efficient configuration is selected. A final model is designed to minimize cogging torque and torque ripple for the chamfer-shaped permanent magnet. Finally, the effectiveness of the final model is validated through FEA by comparing its performance with that of the reference model.

Electric Water Pumps (EWPs) are being adopted more widely to improve thermal management in internal combustion engines and electrified powertrain systems. In this context, the drive motor must deliver high efficiency and reliability despite a strict volume constraint. This paper addresses a key drawback of coreless printed circuit board (PCB) stator axial-flux permanent-magnet machines for EWP use: the PCB traces are directly exposed to the magnet flux, which increases AC loss, while the required phase resistance also leads to non-negligible DC copper loss. To mitigate both loss components within the same conductor design space, a pyramid trace concept is introduced. A magnetic equivalent circuit (MEC) based model is first used to estimate the baseline performance as the number of PCB stator modules changes, and the resulting scalability is examined in terms of module commonality. The final design then applies the pyramid trace layout with a layer-dependent trace width that is narrower on the layers closer to the magnets and wider on the layers farther away—the trade-off between AC loss and DC loss is optimized using 3D finite element analysis. Torque predictions from the simplified MEC model are cross-checked against 3D finite element analysis (FEA), and finally, a prototype is built to validate the analysis with experimental measurements; for the final selected model, the torque prediction error is 2.37% compared with the validation result.

Interior Permanent Magnet Synchronous Motors (IPMSMs) are widely used in the electrification sector; however, reliance on rare-earth magnets imposes constraints stemming from supply instability and mining-related environmental impacts, raising sustainability concerns. To address these issues, this study investigates an IPMSM employing a consequent pole (CP) structure, in which one permanent magnet pole is replaced by iron. Because flux asymmetry in CP IPMSMs can cause torque ripple and associated vibration and noise, we propose an Intersect Consequent Pole (ICP) rotor geometry and evaluate it against a conventional IPMSM under identical stator conditions. The proposed ICP topology reduces permanent magnet usage and provides a rare-earth-reduced design alternative that addresses the vibration/noise trade-off, with a particular focus on electric power steering (EPS) applications. Electromagnetic characteristics and performance were analyzed using finite element analysis (FEA) and verified via FEA-based comparisons.