Jia Liu

Dr. Jia Liu


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 February 2024 in Toxics
Verified
Journal Article
Open access
PDF file
ZZZhengqing Zhou
Zhengqing Zhou
YLYuzhe Liu
Yuzhe Liu
HJHuiling Jiang
Huiling Jiang
ZBZhi-ming Bai
Zhi-ming Bai
LSLingxia Sun
Lingxia Sun
WZWenwen Zhao
Wenwen Zhao
In order to investigate the impact of environmental temperature and atmospheric humidity on the leakage and diffusion of hydrogen fluoride (HF) gas, this study focused on the real scenario of an HF chemical industrial park. Based on the actual dispersion scenario of HF gas, a proportionally scaled-down experimental platform for HF gas leakage was established to validate the accuracy and feasibility of numerical simulations under complex conditions. Using the validated model, the study calculated the complex scenarios of HF leakage and diffusion within the temperature range of 293 K to 313 K and the humidity range of 0% to 100%. The simulation results indicated that different environmental temperatures had a relatively small impact on the hazardous areas (the lethal area, severe injury area, light injury area, and maximum allowable concentration (MAC) area) formed by HF gas leakage. At 600 s of dispersion, the fluctuation range of hazardous area sizes under different temperature conditions was between 3.11% and 13.07%. In contrast to environmental temperature, atmospheric relative humidity had a more significant impact on the dispersion trend of HF leakage. Different relative humidity levels mainly affected the areas of the lethal zone, light injury zone, and MAC zone. When HF continued to leak and disperse for 600 s, compared to 0% relative humidity, 100% relative humidity reduced the lethal area by 35.7%, while increasing the light injury area and MAC area by 27.26% and 111.6%, respectively. The impact on the severe injury area was relatively small, decreasing by 1.68%. The results of this study are crucial for understanding the dispersion patterns of HF gas under different temperature and humidity conditions.

8 February 2024 in Catalysts
Verified
Journal Article
Open access
PDF file
ZZZhengqing Zhou
Zhengqing Zhou
YZYinghua Zhang
Yinghua Zhang
ZHZhian Huang
Zhian Huang
JLJia Liu
Jia Liu
JSJinguo Sang
Jinguo Sang
TTTao Tang
Tao Tang
The catalytic partial oxidation of methane (CPOM) to methanol has been regarded as a promising approach for methane utilization, despite that the conversion remains a formidable challenge in the perspective of catalysts. A novel catalyst system of multi-wall carbon nanotubes (MWCNTs) that supported Fe2O3 with existing I2, consisting of non-noble metal and working in weak acid at an ambient temperature, was investigated for CPOM. MWCNTs supported the Fe2O3 catalyst, which was prepared by the impregnation method and characterized via HRTEM, XRD, XPS, FT-IR, and BET techniques. The characterization results reveal that, as a non-noble metal catalyst, the Fe2O3/MWCNTs catalyst had a good catalytic performance and stability in the CPOM. With the variation of reaction pressure and the dosage of Fe2O3/MWCNTs, the catalyst system obtained the highest methane conversion rate of 7.41% and methanol selectivity of 86.3%, which is analogous to that of the equivalently strong acid catalyst system. The I2-Fe2O3/MWCNTs catalyst system has great potential in the application of CPOM under mild, environmentally benign conditions, such as non-noble metal requirement, ambient temperature, and weak acid. The reaction mechanism was discussed.

30 May 2026 in Processes
Verified
Journal Article
Open access
PDF file
YTYuan Tian
Yuan Tian
YZYinghua Zhang
Yinghua Zhang
JLJia Liu
Jia Liu
YGYukun Gao
Yukun Gao
STShengjie Teng
Shengjie Teng
Efficient capture of respirable dust remains difficult in fully mechanized excavation roadways because fine particles readily migrate with airflow beyond the effective spray region. Here, a wind-assisted negative-pressure dust suppression device was developed by integrating annular Venturi entrainment with a mechanical air duct, enabling coupled airflow induction and droplet transport. The device was optimized using nozzle atomization tests, CFD-based orthogonal simulations, and laboratory-scale validation. The results show that an SK508 solid-cone nozzle provides suitable atomization for Venturi-induced suction. Using induced air inlet velocity and diffuser-inlet static pressure as evaluation indicators, the optimal Venturi unit was obtained at 0.1 MPa water pressure, 0.4 MPa air pressure, a 15° diffuser angle, and a throat-center nozzle position. For the integrated device, the best configuration was ten Venturi tubes, an impeller rotational speed of 2400 r/min, and an impeller position of 300 mm from the air duct inlet. In laboratory-scale tests, the complete wind-assisted negative-pressure mode outperformed fan-only, spray-only, wind-assisted spray, and negative-pressure secondary dust suppression modes, achieving maximum total and respirable dust suppression efficiencies of 87.39% and 86.68%. The results demonstrate the feasibility of coupling mechanical airflow with Venturi entrainment and support subsequent field-scale validation.

16 October 2026 in Nanotechnology
Verified
Journal Article
Closed access
PDF file
YZYanjin Zhang
Yanjin Zhang
ZBZhi-ming Bai
Zhi-ming Bai
JLJia Liu
Jia Liu
Constructing type-II heterojunctions is an effective way to enhance the photoelectrochemical (PEC) performance of semiconductor-based materials. In this study, in order to increase the specific surface area, a novel coral-like 3D porous Ta 3 N 5 nanostructure was first synthesized via a hydrothermal method. Subsequently, CdS quantum dots were deposited on the coral-like Ta 3 N 5 substrate by a successive ionic layer adsorption and reaction method with 40, 80, and 120 cycles (named Ta 3 N 5 /CdS-40, Ta 3 N 5 /CdS-80, and Ta 3 N 5 /CdS-120) to modulate the band structures and optical absorption properties of the composites. The results show that Ta 3 N 5 /CdS-80 exhibits a continuous and dense CdS overlayer with effectively passivated surface states, delivering the optimal PEC performance (3625 μ A·cm −2 at +1 V about 39 times that of the pure Ta 3 N 5 ). This is because the Type-II heterojunction between CdS and Ta 3 N 5 facilitates the separation of photogenerated carriers, and the high-quality CdS coating reduces the capture of photogenerated carriers by defects. When coupled with 304 stainless steel, Ta 3 N 5 /CdS-80 yields a photovoltage drop of 0.39 V and a net photocurrent density of 99.39 μ A·cm −2 , significantly outperforming the Ta 3 N 5 /CdS-40 and Ta 3 N 5 /CdS-120 samples. This work provides experimental evidence for the development of superior Ta 3 N 5 -based photogenerated cathodic protection materials.