In order to investigate the mechanism of mechanical performance enhancement and the curing mechanisms of acrylate emulsion (AE) in cement and magnesium slag (MS) composite-stabilized soil (AE-C-M), this study has conducted a comprehensive analysis of the compressive strength and microstructural characteristics of AE-C-M stabilized soil. The results show that the addition of AE significantly improves the compressive strength of the stabilized soil. When the AE content is 0.4%, the cement content is 3%, and the magnesium slag content is 3% (AE4-C3M3), the strength of the formula reaches 4.21 MPa, which meets the requirements of heavy traffic load conditions in the construction of high-speed or main road base layers. Some reactive groups on the polymer side chains (-COOH) engage in bridging with Ca2+ and RCOO− to form a chemically bonded interpenetrating network structure, thereby enabling the acrylate emulsion to enhance the water damage resistance of the specimens. The notable improvement in strength is attributed to the film-forming and solidifying actions of AE, the binding and filling effects of C-S-H gel, and the reinforcing effect of straw fibers. FT-IR and TG-DSC analysis reveals the presence of polar electrostatic interactions between AE and the soil matrix. AE enhances the bonding among soil particles and facilitates the attachment of C-S-H gel onto the surfaces of the straw fibers, thereby increasing the strength and toughness of the material. The application of MS in conjunction with straw fibers within polymer-modified stabilized soil serves to promote the recycling of waste materials, thereby providing an environmentally friendly solution for the engineering application of solid waste.
This article intends to study the influence of micro-texture and Vickers hardness on the Polished Stone Value (PSV) of four types of high friction aggregates (90# Bauxite, 75# Bauxite, Basalt, and Granite) during the long-term polishing process. For this purpose, profile roughness, Vickers hardness, and PSV were tested. The relationship between profile roughness, Vickers hardness, and PSV was analyzed with gray correlation analysis and mathematical fitting. The results show that arithmetic mean roughness (Ra) and maximum height (Rz) influenced PSV significantly while root mean square height (Rq), skewness (Rsk), kurtosis (Rku), and load length ratio (Rmr (c)) had a relatively weak effect. Because of the high correlation with PSV, Ra and Rz were chosen as indicators, and the relationship between variables (Ra, Rz) and PSV was established. There is a good linear relationship between the attenuation rate of Ra and Rz per polishing cycle (K1 and K2) and Vickers hardness. Finally, a model of estimation of the polished stone value of high friction aggregate based on micro-texture and Vickers hardness during the long-term polishing process is developed. Measuring the profile roughness and Vickers hardness to obtain Ra, Rz, and H correlation values and substituting them into the modeling equations in this paper can be used for optimal selection and life estimation of high friction aggregates, which belong to the raw materials, and the optimal selection of high friction aggregates will be helpful for the design of wear-resistant coatings, especially for high friction surface treatments.
To address the dual challenges of cryogenic performance degradation and excessive VOC emissions in rubberized asphalt, this study proposes a synergistic optimization strategy using a polymer-based warm-mix additive (USP). The effects of USP on the rheological behavior, VOC emission characteristics, and mechanical performance of polymer-modified asphalt and fiber-reinforced RAP interlayers were systematically investigated. The results indicate that 5% USP optimally improves low-temperature flexibility (141.1% increase in ductility, 28.48% reduction in creep stiffness) while maintaining adequate high-temperature stability, and simultaneously achieves an 82.01% reduction in total VOC emissions at 150 °C. Microscopic analysis and DIC tests confirm that USP enhances polymer–asphalt–aggregate interactions, leading to improved adhesion, reduced water permeability, and extended fatigue life. This work provides a fundamental understanding of polymer–binder–aggregate synergy and offers a practical pathway toward greener, high-performance recycled asphalt pavement technologies.
11 February 2026 in Journal of Materials Engineering and Performance