This study investigates the use of waste plastic (polyethylene and polypropylene) and foundry sand to manufacture eco-friendly paver blocks, providing a sustainable alternative to conventional materials. The project aims to address the challenges of plastic waste disposal and environmental damage caused by sand mining. Twelve paver block samples were prepared with varying proportions of plastic (30%–60%) and foundry sand, with or without coarse aggregate. The mechanical properties, including compressive strength, flexural strength, water absorption, and fire resistance, were tested following ASTM standards. The optimal mix, FPA-2 (40% plastic, 40% foundry sand, 20% coarse aggregate), exhibited a compressive strength of 27 N/mm2 and a flexural strength of 6.7 N/mm2, comparable to traditional paver blocks. Water absorption rates were below 7%, and the blocks met fire resistance criteria. Cost analysis revealed that plastic-based paver blocks are up to 25% cheaper than conventional ones, enhancing their economic feasibility. By repurposing waste materials, this study offers a sustainable solution for reducing natural resource dependency and mitigating environmental harm. The findings highlight the potential for plastic-based paver blocks to promote circular economy practices, maintain performance standards, and provide cost-effective alternatives for the construction industry.
An ultrasonic treatment was used to ensure that the nano zinc oxide abbreviated ZnO, was uniformly dispersed throughout the cement paste mixture with addition of fly ash, replacing 10% of the weight of cement. The characteristics of the cementitious mixture were investigated in this research work. The experimental work was carried out by adding nano-ZnO in increments of 0%, 0.25%, 0.5%, 0.75% and 1% by weight of cement, resulting in changes in the characteristics of the concrete paste. The quantity of nano-ZnO present in the cementitious mixture had a notable influence on the consistency of the cement. This impact was also found when the cement paste contained only 0.5% cement by weight. The electrical resistance studies found that the inclusion of nano-sized particles can both delay the hydration of blended cement mix and increase the hydration rate. The findings of experiments revealed that increasing the nano-ZnO concentrations in the cement paste resulted in greater long-term strength. Furthermore, the pore diameter distribution was optimized by the inclusion of nano-ZnO and a tight microstructure was formed in the cementitious mixture at 28 days.
Aluminium alloys find diverse applications in building construction. Specifically, C-profiles being used as various structural elements in the building. Providing Edge stiffeners in the C-profile leads to increase the load carrying capacity. Limited research is available on compression behaviour c-profile with edge stiffeners. Hence, this article aims to study the behaviour of a Finite Element Analysis of aluminium alloy stiffened edge C profiles subjected to axial compression. Two different aluminium alloy materials, namely 6061-T6, and 6063-T5 were investigated. Finite element models were developed and results, including ultimate load, failure modes, and load vs. axial shortening curves, were verified against existing test data. A comprehensive parametric study was carried out based on the verified finite element models, involving variation in the orientation of the edge stiffener, column length, and section thickness. A total of 144 parametric results were compared with the design strengths calculated from Euro code 9.
Concrete is brittle substance whose tensile strength and flexural strength are low and may easily crack and its lifespan is limited. The proposed research aims at assessing how the addition of nylon fiber affects the mechanical and workability of M30 grade reinforced cement concrete (RCC). The originality of this study is that the nylon fibers used are used at optimal dosage (0.25% and 0.5% by volume) in order to improve both strength and durability without impairing the workability. Six series of specimens were cast and experimented on compressive, split tensile and flexural strength, and slump cone testing of fresh concrete workability. The findings showed that the compressive, split tensile and flexural strengths were increased by 11, 14 and 17 percent respectively by the addition of 0.5 percent nylon fiber over plain M30 concrete. The enhancement in mechanical performance is attributed to improved fiber matrix interfacial bonding and crack-bridging mechanisms provided by the dispersed nylon fibers. The fibers effectively delay crack propagation and redistribute tensile stresses within the concrete matrix. Engineering wise, the nylon fiber-reinforced concrete is a cost-effective and structural-friendly substitute of structural application in which enhanced tensile and flexural strengths are needed.
12 April 2024 in Environment, Development and Sustainability