昌兴 刘

Mr. 昌兴 刘

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 December 2025 in Aerospace Science and Technology
Verified
Journal Article
Closed access
XLXiang Li
Xiang Li
HZHuiliu Zhang
Huiliu Zhang
昌刘昌兴 刘
昌兴 刘
JGJingyi Gao
Jingyi Gao
Po LiPo Li
Po Li

25 November 2024 in Control Engineering Practice
Verified
Journal Article
Closed access
PLPo Li
Po Li
昌刘昌兴 刘
昌兴 刘
XTXiaoshan Tong
Xiaoshan Tong
XLXiang Li
Xiang Li
Gaofeng ZhengGaofeng Zheng
Gaofeng Zheng

1 May 2016
Verified
Conference Paper
Closed access
HSH. Y. Sun
H. Y. Sun
KWK. Wang
K. Wang
昌刘昌兴 刘
昌兴 刘
YHY. H. Hu
Y. H. Hu
This paper compares the electromagnetic performance of three phase 24-slot/8-pole surface-mounted permanent magnet (SPM) machines with various permanent magnet shapes, in which the overlapping winding is employed. The permanent magnets (PM) on the rotor are designated as conventional one, sine shape, and sine shape with third harmonic injection. It is found that compared with machines with Sine-shaped PMs, the average torque of machines with Sine+3rd-shaped PMs can be improved by>9% but the cogging torque increases. The increased cogging torque can be reduced by optimizing the configurations of machines such as the width of slots, yoke and teeth. The third harmonic in the airgap flux density is introduced by the PM rotor of sine shape with third harmonic injection, and thus the iron losses are also compared among the machines with different PM shapes.

1 May 2016
Verified
Conference Paper
Closed access
XCX. Chen
X. Chen
KWK. Wang
K. Wang
HSH. Y. Sun
H. Y. Sun
昌刘昌兴 刘
昌兴 刘
YHY. H. Hu
Y. H. Hu
The influence of magnetization on the electromagnetic performance in the surface-mounted permanent magnet (SPM) machine with sinusoidal+3rd harmonic shaped rotor is investigated in this paper. The flux density, cogging torque, phase back-EMF, torque and loss are analyzed by finite element (FE) method. The differences of electromagnetic performance between the machines with parallel and radial magnetization manners are illustrated. It is found that the machine with parallel magnetization can produce high torque but also accompanied by high torque ripple compared to that with radial magnetization.

10 December 2025 in Symmetry
Verified
Journal Article
Open access
PDF file
XGXin Gao
Xin Gao
YHYuanyuan Huang
Yuanyuan Huang
SLshaojie Li
shaojie Li
昌刘昌兴 刘
昌兴 刘
ZSZhongqing Sang
Zhongqing Sang
As a multi-switching power electronic circuit with complex variable topology, the three-level active neutral point clamped (ANPC) converter is a complex system with strong coupling and low linearity. It has numerous high-speed switching devices, a large number of switch states, and a high matrix dimension. Modeling each switch will undoubtedly further increase the circuit size. While in real-time simulation, updating all states of the model to produce outputs within a single time step results in a significant computational load, causing an increasing consumption of FPGA hardware resources as the number of switches and circuit size grow. In order to solve this problem, the current common practice is to decompose the entire complex power electronic system into smaller serial subsystems for modeling. The overall modeling approach for small circuits can be achieved, but when the size of the circuit increases, the overall modeling complexity and difficulty are increased or even impossible to achieve. Decoupling power electronic circuits with this decomposition into subsystem modeling not only reduces the matrix dimension and simplifies the modeling process, but also improves the computational efficiency of the real-time simulator. However, this inevitably generates simulation delays between different subsystems, leading to numerical oscillations. In an effort to overcome this challenge, this paper adopts the method of parallel computation after subsystem partitioning. There is no one-beat delay between different subsystems, and there is no loss of accuracy, which can improve the numerical stability of the modeling and can effectively reduce the step length of real-time simulation and alleviate the problem of real-time simulation resource consumption. In addition, to address the problems of low accuracy due to the traditional forward Euler method as a solver and the possibility of significant errors at some moments, this paper uses a modified prediction correction method to solve the discrete mathematical model, which provides higher accuracy as well as higher stability. And, different from the traditional control method, this paper uses an improved FCS-MPC strategy to control the switching transients of the ANPC model, which achieves a very good control effect. Finally, a simulation step size of less than 60 ns is successfully realized by empirical demonstration on the Speedgoat test platform. Meanwhile, the accuracy of our model can be objectively evaluated by comparing it with the simulation results of the Matlab Simpower system.

1 January 2026 in IEEE Transactions on Transportation Electrification
Verified
Journal Article
Closed access
Po LiPo Li
Po Li
昌刘昌兴 刘
昌兴 刘
XLXiang Li
Xiang Li
GZGanglei Zhao
Ganglei Zhao
Gaofeng ZhengGaofeng Zheng
Gaofeng Zheng