G. V. Naveen Prakash

G. V. Naveen Prakash

Auto-generated profile, based on publicly available information

G. V. Naveen Prakash

Department of Mechanical Engineering, Vidyavardhaka College of Engineering, Mysuru 570002, Karnataka, India

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2015 in Materials Today: Proceedings
Verified
Journal Article
Closed access
BGB.M.UMesh Gowda
B.M.UMesh Gowda
HRH.V. Ravindra
H.V. Ravindra
GPG.V.NAveen Prakash
G.V.NAveen Prakash
PNP. Nishanth
P. Nishanth
GUG. Ugrasen
G. Ugrasen

1 January 2015 in Materials Today: Proceedings
Verified
Journal Article
Closed access
GUG. Ugrasen
G. Ugrasen
HRH.V. Ravindra
H.V. Ravindra
GPG.V. Naveen Prakash
G.V. Naveen Prakash
YPY.N. Theertha Prasad
Y.N. Theertha Prasad

1 January 2017 in Materials Today: Proceedings
Verified
Journal Article
Closed access
PJPrathik S Jain
Prathik S Jain
HRH.V. Ravindra
H.V. Ravindra
GUG. Ugrasen
G. Ugrasen
GPG.V. Naveen Prakash
G.V. Naveen Prakash
YRY.S. Rammohan
Y.S. Rammohan

15 December 2023 in Engineering Proceedings
Verified
Conference Paper
Open access
PDF file
VBVINAY K B
VINAY K B
GPG. V. Naveen Prakash
G. V. Naveen Prakash
DGD. S. Rakshith Gowda
D. S. Rakshith Gowda
NSNithyananda B S
Nithyananda B S
RKRanjith K
Ranjith K
SNSrikantamurthy Ningaiah
Srikantamurthy Ningaiah
Present work focusses on investigating the effect of process parameters such as feed rate and spindle speed on quality characteristics of the hole, i.e., surface roughness (Ra) and circularity at entry and exit in the drilling of aluminium (Al) 6061 reinforced with different volume fraction of silicon nitride (Si3N4). Optimum parameters for Ra and circularity of hole at entry and exit are obtained as feed rate at 0.125 mm/rev, spindle speed at 300 rpm, diameter of drill at 8 mm, and % Vol. of Si3N4 at 5%. Using Analysis of Variance (ANOVA), we observed that spindle speed is the most influential parameter followed by feed rate.

4 January 2024 in Engineering Proceedings
Verified
Conference Paper
Open access
PDF file
NSNithyananda B S
Nithyananda B S
GPG. V. Naveen Prakash
G. V. Naveen Prakash
NANaveen Ankegowda
Naveen Ankegowda
VBVINAY K B
VINAY K B
AAA. Anand
A. Anand
India imports fossil fuels to meet its energy needs, and the need is anticipated to increase over the coming years. The constant usage of crude fuel will initiate its depletion in due course, necessitating the hunt for substitute fuels. One of the most promising alternatives to fossil fuels is determined to be biofuels. Fuels made from second-generation feedstocks, particularly non-edible oils, may change the game in this situation. The use of Simarouba non-edible oil as a substitute for diesel in common rail direct injection (CRDI) engines is the subject of the current piece of research. Running a CRDI engine with Simarouba biodiesel blends may not be suitable under the same operating conditions as running a diesel engine. To optimize performance, the ideal conditions for operating a CRDI engine with Simarouba biodiesel mixes needs to be discovered. The control settings in this study that affect the engine’s performance viz., fuel temperature (FPT), fuel injection pressure (IP), and injection time (IT) are designed using the Taguchi technique. Under full load conditions of 12 kg, for the biodiesel blends viz., SB5, SB10, and SB20, studies were conducted using the Taguchi L9 orthogonal array (OA). Through experimentation, performance and emission responses were obtained. For analysis, six engine responses were considered. The analysis shows that each response is uniquely impacted by the engine control parameters. Therefore, it might be challenging to pinpoint the ideal circumstances that would improve performance and lower emissions. Thus, this presents an example of a multi-response optimization problem. For this reason, multiple response optimization uses Taguchi-Grey Relational Analysis (TGRA). According to TGRA, the ideal settings to increase engine performance while using Simarouba biodiesel blends as fuel are an FPT of 40 °C, an IT of 21° bTDC, and an IP of 600 bar.

27 June 2018 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
GUG Ugrasen
G Ugrasen
HRH V Ravindra
H V Ravindra
BUB M Umeshgowda
B M Umeshgowda
YCY D Chethan
Y D Chethan
GPG V Naveen Prakash
G V Naveen Prakash
Wire cut Electrical Discharge Machining (WEDM) is a special form of EDM process in which electrode is a continuously moving conductive wire. The material removal is by controlled erosion through a series of repetitive sparks between workpiece and wire electrode. WEDM is a specialized thermo electrical machining process capable of accurately machining parts with varying hardness or complex shapes. Present study outlines the estimation of machining performances in the wire electric discharge machining of Cu-1Cr-0.1Zr alloy using Group Method of Data Handling (GMDH) technique and Artificial Neural Network (ANN). Cu-1Cr-0.1Zr alloy was machined using different process parameters based on Taguchi's L27 standard orthogonal array. Parameters such as pulse-on time, pulse-off time and current were varied. The response variables measured for the analysis are Dimensional Error (DE), Surface Roughness (SR), Volumetric Material Removal Rate (VMRR) and Electrode Wear (EW). Machining performances have been compared using sophisticated mathematical models viz., GMDH and ANN. The GMDH algorithm is designed to learn the process by training the algorithm with the experimental data. Different GMDH models can be obtained by varying the percentage of data in the training set and the best model can be selected from these, viz., 50%, 62.5% & 75%. Three different criterion functions, viz., Root Mean Square (Regularity or RMS) criterion, Unbiased criterion and Combined criterion were considered for estimation. Machining performances is predicted for 70% of data in training set using ANN. Estimation and comparison of machining performances were carried out using GMDH and techniques.