Bubble drag reduction has been shown to be a promising technique for reducing the drag in ships, thus reducing the emission of pollutants and allowing the compliance with the new requirements imposed recently in this respect. Different searches have been conducted in the publications related to this technique, and an increase in interest has been shown, especially in the last decade. In this context, a review of the experimental work related to bubble drag reduction published in the last decade is presented in the present article. The works were classified according to the facility used (towing tank, cavitation tunnel, water channel, Taylor–Couette…), and the main finding are presented. It was found that two new trends in research have arisen, while there are still contradictions in the fundamental basis, which needs further study.
This research work is based on a previous study by the authors that characterized the behavior of FBG sensors with a polyimide coating in a structural monitoring system. Sensors applied to structural health monitoring are affected by the presence of simultaneous multidirectional strains. The previous study observed the influence of the transverse strain () while keeping the longitudinal strain constant (), where the x direction is the direction of the optical fiber. The present study develops an experimental methodology consisting of a biaxial test plan on cruciform specimens with three embedded FBG sensors coated with polyimide, acrylate, and ORMOCER®. Applying the Strain–Optic Theory as a reference, a comparison of the experimental values obtained with the different coatings was studied. This experimental work made it possible to study the influence of the transverse strain () on the longitudinal measurements of each FBGS and the influence of the coating material. Finally, the calibration procedure was defined as well as (strain sensitivity factor) for each sensor.
This article presents the design and manufacturing of a hydrogen-powered unmanned aquatic surface vehicle (USV) hull. The design process comprised three stages: (1) defining the requirements for a preliminary geometry, (2) verifying the hydrodynamic hull performance using computational fluid dynamics (CFD) simulations, and (3) experimentally validating the hydrodynamic hull performance and CFD analysis results through experimental fluid dynamics in a calm water towing tank. The manufacturing process utilized additive manufacturing technologies, such as fused granular fabrication and selective laser sintering, to produce the hull and other components, including the propeller and the rudder; thermoplastic materials with carbon fiber reinforcement were employed. The experimental results demonstrate that the optimized trimaran hull exhibited low hydrodynamic resistance (7.5 N), high stability, and a smooth flow around the hull (up to 2 m/s). The design and manufacturing of the USV hull met expectations from both hydrodynamic and structural perspectives, and future work was outlined to integrate a power plant, navigation system, and scientific equipment.
This research work has been based on a previous study by the authors that characterized the behavior of a polyimide-coated FBG sensor in a structural monitoring system. Sensors applied to structural health monitoring are affected in the presence of a state of multidirectional strains simultaneously. The previous study observed the influence of transverse strain (ε_y) while keeping longitudinal strain constant (ε_x), where the direction x is the direction of the optical fiber. The present study developed an experimental methodology which has consisted of carrying out a campaign of biaxial tests on cruciform specimens with three embedded FBG sensors coated with polyimide, acrylate and ORMOCER®. Applying the Strain–Optic Theory as reference, a comparison of the results obtained with the different coatings has been studied. This experimental work has done it possible to study the influence of transverse strain (ε_y) in the longitudinal measurement of each of the FBG sensor and the influence of the coating material. Finally, the calibration procedure as well as the strain sensitivity factor K for each sensor has been defined.
Ice accretion on aircrafts due to atmospheric conditions is still a relevant research topic, especially in the case of Unmanned Aerial Vehicles (UAVs), due to their smaller size and the relative underdevelopment of ice protection systems (anti-icing and de-icing) for these aircraft. For the research and development of these systems, it is necessary to assess their performance in icing wind tunnels (IWTs), which are generally high-cost facilities. This article describes the design and building process of a new IWT for testing fixed-wing UAVs, aimed at cost reduction and restricted to an existing cold climate chamber of limited size. The designed IWT is an open-circuit type with two corners, a test section size of 0.40 m × 0.27 m and speed up to 70 m/s. The design process employs widely used and proven semi-empirical formulas, supported by detailed calculations using Computational Fluid Dynamics (CFD) tools, to achieve a test section core of useful quality and avoid flow separation. Theoretical limits with respect to a usable droplet size and Liquid Water Content (LWC) are calculated, and the test section core is estimated. The design process followed proves to be a very good approach to the design and aerodynamic optimisation of a low-cost IWT.