Considering the full dynamics of the different conversion stages from ocean waves to the electricity grid is essential to evaluate the realistic power flow in the drive train and design accurate model-based control formulations. The power take-off system for wave energy converters (WECs) is one of the essential parts of wave-to-wire (W2W) models, for which hydraulic transmissions are a robust solution and offer the flexibility to design specific drive-trains for specific energy absorption requirements of different WECs. The potential hydraulic drive train topologies can be classified into two main configuration groups (constant-pressure and variable-pressure configurations), each of which uses specific components and has a particular impact on the preceding and following stages of the drive train. The present paper describes the models for both configurations, including the main nonlinear dynamics, losses and constraints. Results from the mathematical model simulations are compared against experimental results obtained from two independent test rigs, which represent the two main configurations, and high-fidelity software. Special attention is paid to the impact of friction in the hydraulic cylinder and flow and torque losses in the hydraulic motor. Results demonstrate the effectiveness of the models in reproducing experimental results, capturing friction effects and showing similar losses.
25 July 2024 in Journal of Intelligent Material Systems and Structures
Traditional valve-controlled hydraulic cylinders are usually very inefficient due to power loss through the control valve. An efficient alternative architecture is to distribute power electrically rather than hydraulically to a group of cylinders and drive each cylinder via individual servomotor-driven pumps. This arrangement is called electrohydrostatic actuation. Such actuators are currently available for power ratings of several hundred watts or greater, but not in the sub-100 W range. This paper details the design, simulation and testing of a piezopump which is intended to address this gap. The motivation is for aerospace applications, and in particular accessory actuators used in the landing gear system. The 10–100 W range is a high-power output for a piezopump, and to achieve this a novel design using disc-style reed valves was developed to allow pumping frequencies above 1 kHz. These high frequencies necessitated the development of custom power electronics capable of delivering 950 V peak-peak sine wave excitation to a largely capacitive load. Experimental results show that the piezopump is capable of delivering over 30 W of hydraulic power, and at no-load can deliver up to 2 L/min of flow at 1250 Hz. Future development includes a transition to multi-cylinder pumps, and improved reed-valve modelling to improve the accuracy of simulated performance.
21 February 2018 in Journal of Ocean Engineering and Marine Energy
Oscillating surge wave energy converters (OSWECs) offer the possibility to convert ocean wave energy in the near shore region into electricity. One of the unique challenges they present is that the forces experienced in each direction differ. The curved geometry of the CCell device exaggerates this difference. Presented in this paper is a novel method of dealing with this difference which does not rely on high buoyancy within the paddle but, instead, variations in the control signals. This reduces the likelihood and severity of end stop collisions , resulting in improved survivability and reduced lifetime costs without increasing the volume and cost of the device. The algorithm presented may further be used to compensate for individual manufacturing tolerances or deterioration to OSWECs whilst in operation.
Hydraulic actuation systems are widely used in industries such as aerospace, the marine industry, off-highway vehicles, and manufacturing. There has been a shift from the hydraulic distribution of power from a centralized supply to electrical power distribution, to reduce the maintenance requirements and weight and improve the efficiency. However, hydraulic actuators have many advantages, such as power density, durability, and controllability, so the ability to convert electrical to hydraulic power locally to drive an actuator is important. Traditional hydraulic pumps are inefficient and unsuitable for low-power applications, making piezopumps a promising alternative for the conversion of electrical to hydraulic power in the sub-100 W range. Currently, the use of piezopumps is limited by their maximum power (typically a few watts or less) and low flows. This paper details the design, simulation, and testing of a multi-cylinder piezopump designed to push the envelope of the power output. The simulation results demonstrate that pumps with two or three cylinders show increasing benefits in terms of hydraulic and electrical performance due to the reduced flow and current ripple compared to a single-cylinder pump. The experimental results from a two-cylinder pump confirm this, and the effect of the phase relationship between the drive signals is investigated in detail. The experimental pump has fast-acting disc-style reed non-return valves, allowing piezostack drive frequencies of up to 1.4 kHz to be used. Custom power electronics tailored to the pump are developed. These features are critical in demonstrating the potential for multi-cylinder piezopumps to play an important role as a future actuation solution.