We present a numerical investigation of an acoustic sensor based on a cylindrical resonator to monitor the acoustic properties of liquids flowing in a tube. The sensor design consists of a hollow cylindrical washer surrounding the tube, which carries the liquid, and which can be filled during the sensing process. Due to the impedance mismatch between the liquid and the solid washer, we demonstrate the presence of high-quality factor resonances associated with the acoustic properties of the liquid (such as velocity, density, or viscosity) appearing as sharp spectral features in the transmission and detection measurements. An appropriate choice of geometrical parameters allows either to obtain two distinct resonances associated with the liquid and the surrounding washer or to overlap the narrow resonance of the liquid with the broad resonance of the washer and achieve a Fano-type resonance from their interaction. The sensitivity of the resonances to the acoustic properties of the liquid are investigated as a function of the geometrical parameters. We show that for highly viscous fluids, the vanishing of very narrow peaks can be avoided by increasing the thickness of the washer and, therefore, decreasing the quality factors. The calculations are performed in the framework of a finite element method. Our design provides a promising platform for sensing several acoustic characteristics of liquids flowing in tubes.
Monometallic (Ni, Co or Fe-SiC(O)) and bimetallic (Ni, Co or FeM-SiC(O) with M = Ni or Co) ceramic nanocomposites have been successfully prepared using polymeric precursors obtained by chemical modification of polycarbosilane with metal acetylacetonate. The nanocomposites consist of homogeneously distributed metal nanoparticles within an amorphous SiC(O). The specific surface area (SSA) of Ni, Co or Fe-SiC(O)600 nanocomposites were found to be 155, 50 or 14 m2/g. However, the addition of Fe to the Ni-or Co-containing precursors tends to increase the SSA to 290 or 170 m2/g. Maximum CO2 conversion for monometallic samples was found to be 40% at 500 °C for Ni-SiC(O)600 and maximum CH4 selectivity was 61% at 300 °C for Co-SiC(O)600. The additional presence of Co and Ni in the respective nanocomposites helps to increase the CO2 conversion and selectivity at 500 °C whereas Fe modification shows high methane selectivity at lower temperature < 350 °C. Graphical Abstract
Silica aerogels are highly porous materials with unique properties such as high specific surface area, high thermal insulation, and high open porosity. These characteristics make them attractive for several applications in closed microfluidic channels such as BioMEMS, catalysis, and thermal insulation. However, aerogel-filled microchannels have not been reported in the literature yet because of the complexity of creating a process that controls the integration, shrinkage, and mechanical stability of these materials inside a closed channel. In this work, a process is presented to integrate aerogels in microchannels with reproducibility, mechanical stability, and no shrinkage. This protocol is based on the filling of channels during the gelation, which is crucial to avoid shrinkage, CO2 supercritical drying, and mechanical additives (polyethylene glycol and carbon nanotubes). Furthermore, the influence of polyethylene glycol and carbon nanotubes on the compressive strength, porosity, and specific surface area is investigated. Following the suggested process protocol, the integration of different aerogel compositions (with and without reinforcement) is successfully achieved in the microchannels without shrinkage and cracks. This research opens up new possibilities for the use of different aerogels in microfluidics with structural integrity and enhanced functionality.
14 November 2025 in Journal of Materials Science: Materials in Engineering
Hydrogen offers a high-energy, carbon-free fuel alternative; however, conventional flame-based hydrogen combustion poses challenges, including NO x emissions and the risk of flame flashback. Catalytic combustion provides a safer, low-temperature approach to hydrogen utilization, but realizing it within compact, integrated systems have remained a significant challenge. This study introduces an innovative approach to hydrogen catalytic combustion by directly integrating noble metal single quantum-crystallites of Pt and Ru within a porous silica aerogel matrix embedded in a silicon chip. This configuration enables deep nanoparticle ( np ) penetration throughout the aerogel network, maximizing the catalytic surface area and providing efficient on-chip hydrogen combustion. The np @aerogel systems are systematically synthesized and incorporated within silicon chips equipped with a polyimide membrane and Pt thermal structures. This unique setup allows for direct, real-time characterization of hydrogen catalytic combustion by measuring resistance changes in an embedded thermistor. The Pt@SiO₂ system demonstrates a rapid and substantial temperature increase of up to 40 K upon hydrogen exposure, independent of both preheating and Pt concentration, underscoring its robustness and adaptability for micro-scale hydrogen combustion. This on-chip integration of np @aerogel catalysts marks a significant advancement for hydrogen-based energy applications, offering a compact, scalable platform for efficient catalytic combustion. This approach opens pathways for applications in thermoelectric generators and other micro-reactor technologies where controlled, localized energy generation is critical.
Aerogels with noble metals have a wide range of applications such as sensing and catalysis, but research needs to be done to improve the integration of these materials in µ-channels. We realize silica aerogels without shrinkage and with high specific surface area (~600 m2/g) inside of closed channels. Further, Pt nanoparticles are deposited via capillary forces, into the complete network.
We report the realization of metallic 3D microstructures, electroplated in two-photon polymerized molds. These molds are typically 150 × 150 × 30 µm3 in size and the smallest feature size is about 1 µm. After the electroplating process, the mold is removed by means of CF4/O2 etching (1 h). The vertical electroplating growth is about two times higher than the horizontal growth, which creates voids. A new design to prevent voids was tested where the pores were arranged at a 35° angle to the chip surface. The remaining structures consisted of a copper base with a palladium finish, or of pure palladium. They were analyzed through SEM and were shown to be a good reproduction of the mold design, resulting in metallic porous structures with a specific surface area of about 6 mm2/mm2.