Shipping traffic is recognised as the main man-noise source of the anthropogenic noise generated in the marine environment. The underwater acoustic pollution is increased due to the increment of the human activity at seas supposing a threat for marine habitats. The ship as acoustic source must be understood and controlled to manage the maritime areas both in time and space to reduce the impact of noise in marine fauna. Shipping noise is mainly composed of flow noise, propeller noise and machinery noise. This research is focused on the analysis and estimation of the underwater radiated noise generated by the vibrations of the onboard machinery or structure-borne noise based on the calculation of the transfer function. This function relates the acceleration levels of the vibrations of the hull’s panels and the radiated noise by them using the radiation efficiency. Different analytical methods to estimate the radiation efficiency are presented and compared with data collected at sea. The measurements are performed acquiring simultaneously acceleration and acoustic levels by means on accelerometers installed on the hull’s panels at different positions and hydrophones deployed close to the bow, middle and stern of the ship. The analysis of the transmission of the vibrations along the ships is performed using the data from different locations of the hydrophones. The quality of the measurements is analysed using the coherence function through the spectral correlation between the measurement of vibrations and acoustic levels. On the other hand, signal-to-noise ratio is computed to verify the strength of the noise sources. The computed transfer function is used to predict the underwater radiated noise from vibrations showing differences less than 2 dB re to 1 μPa².

This work presents results allowing an unequivocal correlation of the observations of strong nonlinear elastic features of ultrasonic waves (values of the nonlinearity parameters exceeding the thresholds corresponding to undamaged states), with the critical events of the corrosion-induced surface cracking of reinforced cement-mortar specimens. These observations point to the possibility of the early detection of cracking using nonlinear ultrasonic (NLU) techniques. Experimental evidence is presented on the existence of active net mass transport processes, due to wick action, in the course of the corrosion tests, in the experimental conditions of this work. These phenomena might explain the observed abrupt shifting of the nonlinear parameter values (typically increasing and then decreasing post-peak, even reaching values typical of the undamaged state), and, partially, the high variability obtained for the values of the nonlinear parameters in damaged (cracked) states. Finally, some consequences are derived from the point of view of use of the NLU techniques in engineering practice, i.e., in surveys aimed at evaluating reinforced concrete structures affected by corrosion.

Los sistemas anticaída se establecen en UNE-EN-363 para evitar o retener caídas de personas sin que las fuerzas de retención causen daños relevantes. Constituyen el último recurso para prevención de caídas tras considerar otras medidas. Este artículo analiza las variables que afectan al comportamiento del sistema: altura de caída, longitud de cuerda de retención, rigidez y amortiguamiento del material de retención, y peso del operario. A tal fin, el fenómeno ha sido simulado con modelos dinámicos de elementos finitos mediante una cuerda elástica y un lastre rígido. Ello permite obtener valores verosímiles de las máximas fuerzas sobre el accidentado y el sistema durante el impacto. Los resultados demuestran el papel fundamental de la proporción entre altura de caída y longitud de cuerda (factor de caída), más determinante que la propia altura de caída. Las elevadas fuerzas máximas obtenidas indican la necesidad de incluir en el modelo absorbedores de energía elastoplásticos, en futuras investigaciones, con el fin de disminuir el impacto a valores razonables.

The requirements for edge protection systems on most sloped work surfaces (class C, according to EN 13374-2013 code) in construction works are studied in this paper. Maximum deceleration suffered by a falling body and maximum deflection of the protection system were analyzed through finite-element models and confirmed through full-scale experiments. The aim of this work is to determine which value for deflection system entails a safe deceleration for the human body. This value is compared with the requirements given by the current version of EN 13374-2013. An additional series of experiments were done to determine the acceleration linked to minimum deflection required by code (200 mm) during the retention process. According to the obtained results, a modification of this value is recommended. Additionally, a simple design formula for this falling protection system is proposed as a quick tool for the initial steps of design.B. Ferrer acknowledges the support of the Generalitat Valenciana through the project GV/2013/009 and the Spanish Ministerio de Economía y Competitividad through the project BIA2011-22704

Las barandillas de seguridad con solicitación dinámica, tipos B y C según UNE-EN 13374, son el conjunto de componentes destinados a la protección colectiva de las personas contra las caídas a un nivel inferior y a retener materiales. Frecuentemente incorporan una red de seguridad. En este artículo se analizan aspectos fundamentales como su diseño, sus requisitos mecánicos y la solución a la problemática que suponen los soportes o puntos duros capaces de producir lesiones al accidentado. Para este fin, se ha estudiado el fenómeno de la caída de un lastre sobre tales redes con distintos modelos numéricos de elementos finitos en régimen dinámico y mediante consideraciones analíticas cinemáticas, obteniendo conclusiones útiles como la forma geométrica necesaria, la escuadría de los perfiles que constituyen el bastidor de la red, y los factores de impacto que sufren los accidentados. Ello permite sugerir mejoras al texto normativo.