Metal-filled composites based on polypropylene waste have been successfully obtained with an injection molding method of metalized polymer raw materials. Using the model polymer, the peculiarities of the formation of the copper layer in solutions of chemical metallization on the polypropylene surface were investigated and the main factors influencing this process were established. The main influence on the rate of reduction of copper in solutions of chemical metallization has the concentration of copper sulfate, sodium hydroxide, and EDTA-Na2. It was shown that the efficiency of the copper plating process also strongly depends on polymer processing, which follows the activation. In case of the use of simple activation, it is not possible to obtain metalized raw materials with high efficiency. Additional processing of activated polymer raw materials is required to carry out the process with high efficiency. The amount of reduced copper on the polymer surface can be adjusted by changing the concentration of the components of the chemical metallization solution, as well as the degree of loading of the polymer raw material. Examination by electron scanning microscopy of the obtained metalized polypropylene showed that the copper coating on the polymer particles is formed with a high degree of surface coverage. The formed copper coating is free of copper oxides, which is confirmed by X-ray diffraction studies and analysis of the spectrum of characteristic X-rays. Metal-filled composites have been characterized by the effect of copper on mechanical and rheological (MFR) properties. The Differential Scanning Calorimetry (DSC) and Thermogravimetric (TG) methods show a certain effect of metal on the magnitude of thermal effects and the rate of weight loss.
17 May 2018 in Eastern-European Journal of Enterprise Technologies
Influence of concentration of components of chemical metallization solutions on the process of copper reduction on activated polyvinylchloride surface has been studied. It has been established that changes in concentrations of copper sulfate, trilon B and formaldehyde can effectively influence the metallization process. It was shown that the loss of stability of chemical metallization solutions and formation of colloidal solutions makes it is impossible to obtain a metallized polymeric material since copper reduction occurs in the solution volume. Copper reduction in the solution volume occurs because of presence of insoluble colloidal particles of copper hydroxide which are centers of nucleation of copper reduction. At such centers, copper reduction occurs as a result of reaction with formaldehyde and is accompanied by high volumes of hydrogen evolvement. It has been established that the formation of copper coating on an activated polymer surface occurs only with the use of true chemical metallization solutions. The main factor determining stability of chemical metallization solutions is complexing. It was shown that trilon B concentration under 40 mmol/l is not sufficient to bind all Cu2+ ions in a complex which prevents formation of insoluble copper hydroxide in an alkaline medium. The growth of trilon B concentration above 53 mmol/l results in reduction of a portion of copper in a form of hydroxide and formation of true solutions. It has been established that concentration of copper sulfate and alkali exerts the main influence on the mechanism of copper reduction in the case of true solutions. The growth of pH of chemical metallization solutions above 12 brings about an increase in the portion of copper that is reduced by the exchange reaction with zinc.
30 June 2017 in Eastern-European Journal of Enterprise Technologies
A relevant issue today is the principle of energy efficiency and rational use of energy resources. At present, solar heating systems with conventional solar collectors are quite expensive. Given this, we designed and patented a solar roofing, which combines the functions of a solar collector and a metal corrugated part of the pitched roof. The feature of solar roofing is that its heat absorber is made of the corrugated roofing material of the building. This makes it possible to significantly reduce the cost of the solar system, improve its strength and simplify the design.Comprehensive solution of the issues of fixing solar collectors directly to the elements of the roof has broad prospects because, in this case, the possibility of replacing a part of the roof with them can be implemented. This eliminates additional load on the carrying structures and reduces the cost of solar heating in general. We developed a mathematical model of the work of a solar roofing in the heating system, which is a dependence of calculation of heating temperature of the heat carrier in the tank-accumulator on intensity of the heat flow and period of radiation. It was established that at changing incident angles of the heat flow from 90º to 30º, effectiveness of solar roofing reduces insignificantly compared with the flat solar collectors.We improved dependences of change in the efficiency of solar heating systems using a solar roofing on the direction and velocity of the air flow. It is established that energy efficiency of a solar roofing is larger affected by velocity of air flow, while its direction is less important.
29 August 2017 in Eastern-European Journal of Enterprise Technologies
We present kinetic patterns of metallization of zinc-activated polyvinylchloride in the solution of chemical copper plating. The influence was studied of pH of the medium and the amount of metal of the activator on the copper deposition rate on the activated polymeric surface. It was established that in the case of activation of the polymeric surface with zinc, the solution undergoes two competing reactions of copper reduction. By using a volumetric method, we determined that pH of the medium exerts a decisive impact on the reduction mechanism of copper. It is proved that with the growth of pH in the solutions of chemical copper plating and the amount of metal-activator, the amount of copper reduced as a result of exchange reaction with zinc increases. The optimal pH of the solutions for the course of reaction of copper reduction by formaldehyde is 12. The obtained samples of metallized powder-like polyvinylchloride contain a significant quantity of copper on the surface and could be used to create metal-filled composites.The research conducted allows us to establish optimal conditions and effectively influence the copper reduction process on the activated polymeric surface in the solutions of chemical metallization. By changing the speed and efficiency of copper deposition on the polymeric surface, it is possible to control the content of metal in polymeric composites that are obtained from such materials, and thus control their properties
The research studied the feasibility of using copper-coated polyethylene granules as a basis for creating efficient heat storage systems. A technology for imparting catalytic properties to a polymer surface by the joint processing of polymer granules and an activator metal in a ball mill with their subsequent metallization in a chemical reducing solution is proposed. The efficiency of copper-coating a polyethylene surface is shown to be largely determined by the activation stage and the assumption regarding the mechanism of interaction of the activator metal with the polymer surface is made. To obtain different amounts of metal on the polyethylene granules, it is proposed that the method of remetallization is used. It was established that the rate of copper ion reduction depends on the number of previous coatings and is determined by the area of interaction of the metal-coated granules with the chemical reducing solution. The obtained metal-coated polyethylene granules were characterized in terms of the viability of using it as a phase transition material for a heat storage system. Using the developed installation that simulates the heat accumulator operation, it was shown that the efficiency of using metal-coated polyethylene granules to create heat storage systems is higher. The copper coating deposited on the polyethylene granules was studied using scanning electron microscopy and X-ray diffraction analysis.
24 August 2016 in Eastern-European Journal of Enterprise Technologies
Despite the considerable number of papers on elaborating the methods of mathematical modeling of thermal power systems, at present little attention is paid to the development of methods of analysis of the influence of different factors on the performance indicators of work of an energy unit. In this article we substantiated principles of selection and mathematical modeling of the simplest elements of heat transfer systems, which clearly reflect the essence of processes in these systems and are convenient in terms of their mathematical modeling. The use of selection and mathematical description of elementary heat exchangers, mixers and dividers of flows may describe a variety of heat transfer system of any energy plants.These methods allow comparing various modes of operation of the equipment, its design peculiarities and their possible combination significantly faster and economically efficient. A proposed mathematical model of the elements of HTS in the form of a temperature characteristic provides unification of models of all elements, subsystems and HTS as a whole, as well as the clarity and convenience of the description of connections of elements. The calculations of heat transfer systems may be efficiently used for analysis of the work and different types of design and checking calculations of heat transfer convective surfaces. The use of generalized dimensionless parameters makes it possible to perform calculations based on different parameters of the initial information and to improve efficiency of analysis of the work of heat exchangers.