Birnessite-type MnO2 (BM) is a promising anode material for lithium-ion batteries (LIBs) due to its high theoretical capacity and low lithiation voltage. However, its poor conductivity and structural instability limit long-term performance. In this work, we report an optimized in situ hydrothermal synthesis of BM–graphene (BM–Gr) composites, guided by thermodynamic equilibrium modeling using the HSC Chemistry software package to model phase formation. The effects of NaOH/H2O2 concentration, reaction time, and graphene loading on phase stability and morphology were systematically studied and validated experimentally. Structural, morphological, and compositional analyses (XRD, FE-SEM, EDS, TEM, and XPS) confirmed that pure birnessite was successfully synthesized and uniformly anchored on graphene, without secondary phases such as Mn3O4 or MnOOH. Graphene incorporation induced oxygen vacancies (VO) and Mn–O–C interfacial bonding, narrowing the bandgap from 1.7 (BM) to 1.4 eV (BM–Gr). The optimized BM–Gr electrode delivered an initial lithiation capacity of 2097 mAh g−1 and maintained 758 mAh g−1 after 175 cycles at 450 mA g−1, compared to 86 mAh g−1 for BM after 50 cycles. Electrochemical impedance spectroscopy revealed an ~ 18-fold increase in the Li⁺ diffusion coefficient after cycling (7.10 × 10–13 to 1.27 × 10–11 cm2 s−1), attributed to improved ion transport pathways and enhanced structural stability from the conductive graphene framework. These results demonstrate that thermodynamically guided BM–Gr synthesis provides a viable strategy for producing structurally robust, high-capacity anodes for next-generation LIBs.
The suitability of various nitrogen, sulfur, oxygen, and phosphorus compounds as complexing agents in a silver electrolyte was examined by using potentiometric titration under practical conditions. The setup consisted of three electrodes to measure the pH and the activity of the silver ions simultaneously. Different ratios of silver to complexing agent from 1:10 to 1:1 at a constant ionic strength of 0.2 mol/L were investigated. The type of the complexes and their corresponding critical stability constants were evaluated by fitting the measured data using a self-developed algorithm. The pH and Nernst potential curve were calculated for the assumed complexes based on the law of mass action to find the best approximation. The correct definition of the occurring species is challenging and can lead to significant changes in the calculation of stability constants. For this reason, the measured silver potential curves were primarily used for the rating of the complexing agents. An evaluation of the measurements shows that the donor atom of the complexing agent and its ligand field strongly affected the stability and type of the complexes. Only a few complexing agents were found to be suitable for use in the cyanide-free silver electrolyte.
Its crucial importance to the long-term operation of lithium-ion batteries has made the solid electrolyte interphase (SEI) the subject of intensive research efforts. These investigations are challenging, however, due to the very complex and fragile nature of this layer. With its typical thickness being in the range of some 10 nm and its chemical make-up being highly sensitive to even the smallest amounts of impurities, it becomes clear that artifacts are easily introduced in investigations of the SEI, especially if the measurements are performed ex situ. To help ameliorate these issues, we herein report a combination of non-destructive operando techniques that can be employed simultaneously in the same electrochemical cell to provide a plethora of physical, morphological, and electrochemical data on the macroscopic and microscopic scale. These techniques encompass atomic force microscopy (AFM), electrochemical quartz crystal microbalance with dissipation monitoring (EQCM-D), and impedance spectroscopy (EIS). This work focuses on how to combine these techniques in a single electrochemical cell, which is suitable to study SEI formation while avoiding noise, crosstalk, inhomogeneous SEI formation, and other pitfalls.
Aluminum-ion batteries (AIBs) are emerging as promising alternatives to lithium-ion batteries due to their cost-effectiveness and resource abundance. However, their practical application is hindered by low capacity, poor cycle life, and limited rate capability. In this study, δ-MnO2 and δ-MnO2/Graphene composite cathodes are developed and tested in aqueous aluminum-ion batteries (AAIBs) using a mixture of 0.5 M Al2(SO4)3 and 0.4 M MnSO4 as the electrolyte. The electrochemical properties are evaluated alongside treated aluminum (TAl) and Zn–Al alloy anodes. Among the configurations tested, the δ-MnO2/Graphene|0.5 M Al2(SO4)3, 0.4 M MnSO4|Zn–Al system showed the best performance, achieving a high discharge voltage of 1.63 V, a specific capacity of 746 mAh g−1, and excellent cycling stability over 352 cycles. The stabilizing effect of graphene, due to increased oxygen vacancies and the formation of Mn–O–C bonds, enhances electron and ion transport, thereby improving cathode integrity and the overall performance of the AAIB. Additionally, the Zn–Al alloy anode extends the battery’s cycle life compared to the TAl anode. This work demonstrates the potential for low-cost, high-performance AAIBs, paving the way for more sustainable and scalable energy storage solutions.
Electrodeposition is a key surface engineering technology, with chromium coatings widely used to improve tribological, corrosion‐resistant, and aesthetic properties. Due to environmental regulations such as REACH, industry is transitioning from hexavalent to trivalent chromium (Cr(III)) electrolytes. These systems exhibit high physicochemical complexity and strong sensitivity to process fluctuations and contaminants, making conventional trial‐and‐error optimization inefficient. As a result, data‐driven approaches combining experimental and simulation data with machine learning are increasingly used to investigate complex process–structure–property relationships. The effectiveness of these approaches depends on FAIR‐compliant, well‐structured datasets. Semantic web technologies, particularly ontologies, enable the formal representation of domain knowledge and the integration of heterogeneous data into machine‐actionable information. Within the German Platform MaterialDigital (PMD) initiative, domain‐specific ontologies support a federated materials data infrastructure. This work presents two main contributions, namely, the PlatOn ontology, developed in the DigiChrom project to semantically represent galvanic chromium plating and material characterization, and a hybrid Large Language Model (LLM)‐assisted alignment pipeline that maps PlatOn to the PMD Core Ontology (PMDco 3.0) and the Basic Formal Ontology (BFO). This ensures interoperability and enables cross‐ontology querying of electroplating data. Ontology development is supported by a graph‐based engineering workflow using the BWMD mid‐level ontology and the Graph Designer App.