Michael Markushev

Prof. Michael Markushev


Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 December 2015 in Metals
Verified
Journal Article
Open access
PDF file
EVEvgeni Vasilev
Evgeni Vasilev
MLMikhail Linderov
Mikhail Linderov
DNDayan Nugmanov
Dayan Nugmanov
OSOleg Sitdikov
Oleg Sitdikov
MMMichael Markushev
Michael Markushev
AVAlexei Vinogradov
Alexei Vinogradov
Fatigue properties under axisymmetric push-pull loading of a magnesium alloy Mg-6Zn-0.5Zr (ZK60) after processing by multiaxial isothermal forging (MIF) to a total strain of 4.2 at 400 °C were investigated. The strong influence of the microstructure on the mechanical behavior is demonstrated. Hot severe plastic deformation was shown effective in improving the fatigue life in both the high- and low-cyclic regimes.

31 December 2017 in Metals
Verified
Journal Article
Open access
PDF file
MLMikhail Linderov
Mikhail Linderov
EVEvgenii Vasilev
Evgenii Vasilev
DMDmitrii MERSON
Dmitrii MERSON
MMMichael Markushev
Michael Markushev
AVAlexei Vinogradov
Alexei Vinogradov
Corrosion fatigue data for magnesium alloys are still scarce. The present communication reports the results of microstructural investigations and fatigue testing of the fine grain Mg-Zn-Zr (ZK60) alloy after multiaxial isothermal forging and of the hot extruded Mg-Y-Zn (WZ21) alloy in air and in the 0.9% NaCl water solution. Both of the alloys demonstrate a very good high-cycle fatigue performance in air. However, the significant drop of fatigue resistance is observed in the corrosive environment. Results are discussed from perspectives of potential applications and future studies.

1 January 2020 in Letters on Materials
Verified
Journal Article
Open access
PDF file
DMDmitrii MERSON
Dmitrii MERSON
Alexander BrilevskyAlexander Brilevsky
Alexander Brilevsky
PMPavel Myagkikh
Pavel Myagkikh
MMMichael Markushev
Michael Markushev
AVAlexei Vinogradov
Alexei Vinogradov
Magnesium and its alloys have several competitive advantages due to their low density and the highest specific strength among modern structural metallic materials.

24 April 2015 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
DNDayan Nugmanov
Dayan Nugmanov
OSO Sh Sitdikov
O Sh Sitdikov
MMMichael Markushev
Michael Markushev

1 December 2021 in Letters on Materials
Verified
Journal Article
Open access
PDF file
MMMichael Markushev
Michael Markushev
RIRafis Ilyasov
Rafis Ilyasov
SKStanislav Krymskiy
Stanislav Krymskiy
IVIrshat Valeev
Irshat Valeev
OSOleg Sitdikov
Oleg Sitdikov
The effect of a treatment combining isothermal cryogenic rolling and single electro-pulsing on the structure and hardness of M1 grade copper with an initial grain size of 10 –15 μm was investigated.

19 December 2025 in Facta Universitatis, Series: Mechanical Engineering
Verified
Journal Article
Open access
PDF file
MMMichael Markushev
Michael Markushev
IVIrshat Valeev
Irshat Valeev
AVAygul Valeeva
Aygul Valeeva
RIRafis Ilyasov
Rafis Ilyasov
EAElena Avtokratova
Elena Avtokratova
OSOleg Sitdikov
Oleg Sitdikov
A synergy effect of cryorolling and high-dense electric pulsing on the structure, texture and hardness of fine-grain Cu is analyzed. More than twice Cu strengthening under rolling with 90% reduction at –196°С was caused by strong rolling texture and work-hardened nanostructure with ~300 nm crystallites and ~30% fraction of high-angle boundaries. Further single pulsing with current intensity Kj = 3.5×104 A2s/mm4 resulted in a static recovery and slight Cu softening due to the formation of a more equilibrium structure with lower dislocation density and lattice microstrain. Increasing Kj to 3.8×104 A2s/mm4 led to a sharp drop in the Cu hardness owing to continuous recrystallization and texture randomization. At Kj near 5.0×104 A2s/mm4 homogeneous ultrafine-grain structure with 1 μm defect free equiaxed grains and about 30% of twin boundaries is formed. Normal grain growth to 3 µm and gradual decrease of the Cu hardness were taking place at higher pulsing energies, up to 8.1×104 A2s/mm4.