Mengjia Li

Dr. Mengjia Li


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 December 2018 in Journal of the Electrochemical Society
Verified
Journal Article
Closed access
PDF file
XWXue Wang
Xue Wang
JCJing Che
Jing Che
MWMin Wu
Min Wu
YSYaru Shi
Yaru Shi
MLMengjia Li
Mengjia Li
LLLifen Liu
Lifen Liu
In this paper, the application of the surfactants as an anti-fouling and pre-concentrating agent has been investigated for the electrochemical determination of bisphenol A (BPA) on a carbon nanotubes (CNTs) modified glassy carbon electrode. The direct measurement, standing time and stirring time in the BPA solution were studied to repel the oxidation products on electrode surface and reduced electrode fouling to improve the sensitivity of the modified electrode during detection process. After optimization of experimental parameters, the addition of 0.2 g L−1 Tween 20 and a stirring of 30 s both contributed to weaken the fouling effect and increase the sensitivity, in comparison of direct measurement at a bare electrode and a CNTs modified electrode. The oxidation current intensity was proportional to the concentration of BPA with a wide concentration range from 1 to 100 μmol L−1. The limit of detection was 0.3 μmol L−1.

5 April 2020 in Metals
Verified
Journal Article
Open access
PDF file
QLQianqian Li
Qianqian Li
MLMengjia Li
Mengjia Li
GLGuangxi Lu
Guangxi Lu
SGShaokang Guan
Shaokang Guan
EZEngui Zhang
Engui Zhang
Cong XuCong Xu
Cong Xu
The influence of alloying elements Er, Zr, Cu, Si and Zn on the crystallization temperature interval, microstructure, mechanical properties and corrosion behavior of Al-Mg-Mn alloy were studied by differential scanning calorimetry (DSC), electron backscatter diffraction (EBSD), X-ray diffraction (XRD), tensile testing, electrochemical measurements and nitric acid mass loss test (NAMLT). The results show that the crystallization temperature range of Al-Mg-Mn alloy with addition of Zn decreased 4.7 °C. Cold rolled alloys mainly contain S texture, Copper texture, Brass texture, and Goss texture; the content of the S texture is the highest. With the addition of trace elements, the second phase Al3Er, Al3Zr, Al2CuMg, Mg2Si and MgZn2 can be formed, which can improve the tensile strength and yield strength of Al-Mg-Mn alloy. The addition of the alloying element Zn can also improve the intergranular corrosion resistance of the Al-Mg-Mn alloy.

29 July 2024 in Materials Science and Engineering: A
Verified
Journal Article
Closed access
SLShuo Liu
Shuo Liu
XWXiangdong Wang
Xiangdong Wang
YSYunjia Shi
Yunjia Shi
MLMengjia Li
Mengjia Li
QPQinglin Pan
Qinglin Pan

16 July 2022 in Metals
Verified
Journal Article
Open access
PDF file
PYPuyou Ying
Puyou Ying
CLChanghong Lin
Changhong Lin
ZLZhiyi Liu
Zhiyi Liu
SBSong Bai
Song Bai
VLVladimir Levchenko
Vladimir Levchenko
MLMengjia Li
Mengjia Li
In the present work, different aging treatments were performed to investigate the pre-aging effect on the formation of Ω phase and mechanical properties in Al-Cu-Mg-Ag alloy. The results showed that pre-strain could inhibit the formation of Ω phases, which was detrimental to the alloy strength. Due to the introduction of pre-aging treatment before pre-strain, the adverse effect of pre-strain on the precipitation of the Ω phase was reduced, and the alloy strength was increased by at least 15 MPa. Besides this, increasing the pre-aging temperature promoted the precipitation of Ω phases, inhibited the formation of θ′ phases, and improved the alloy strength. This was because the higher pre-aging temperature promoted more pre-precipitated Ω phases in the pre-aging process, and most of the pre-precipitated Ω phases could be retained and grew in the subsequent aging process. As a result, the tensile strength of the alloy increased from 523 MPa to 540 MPa. In addition, pre-aging with a higher temperature consumed more solute atoms, leading to less residual solute atoms in the matrix. Thus, the adverse effects of pre-strain, which inhibit the formation of clusters by the segregation of solute atoms, were reduced.

8 June 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
SMSidra Tul Muntaha
Sidra Tul Muntaha
MLMengjia Li
Mengjia Li
JSJinlong Sun
Jinlong Sun
JWJianfeng Wang
Jianfeng Wang
AHAneela Habib
Aneela Habib
Accurate prediction of mechanical properties in as-cast aluminium alloys remains a critical challenge in alloy design due to the complex, non-linear interplay between chemical composition, solidification thermodynamics, and microstructure. This study presents a machine learning framework augmented with analytically computed thermodynamic descriptors for predicting Vickers hardness (HV) of Al-6xxx series as-cast alloys. Thermodynamic features including phase fractions (f_Mg₂Si, f_Al₃Sc, f_Al₃Zr, f_FCC_Al), liquidus/solidus temperatures, solidification range, and Gibbs mixing energy at 500°C were calculated using simplified analytical expressions implemented in Python, rather than full CALPHAD software, and integrated with conventional compositional and physics-based descriptors.A curated dataset of 69 alloys (HV range: 40–107 HV; mean 84.6 ± 17.0 HV) was assembled from literature, augmented to 150 training samples via Gaussian noise injection, and used to benchmark 11 machine learning models. CatBoost and Stochastic Gradient Boosting emerged as top performers, achieving test R² values of 0.804 and 0.824 respectively, with RMSE below 4.6 HV. External validation on four novel as-cast alloys confirmed strong generalisability, with mean absolute prediction errors of 1.8% (CatBoost) and 1.5% (Stochastic GB). SHAP analysis identified Trace_total, Atomic_size_mismatch, and Excess_Si as the most influential predictors, followed by Mg and Mn. Thermodynamic descriptors contributed meaningfully, with T_liquidus and f_FCC_Al ranking in the top 10. Three inverse design strategies (gradient-based, genetic algorithm, Bayesian optimisation) identified compositions targeting 95 HV. Pareto front analysis revealed 11 cost-optimal compositions spanning 4.18–10.29/kg, with the genetic algorithm proposing a minimum-cost solution at $4.87/kg. Sensitivity analysis quantified marginal effects of each alloying element, providing actionable guidelines for cost-efficient Al-6xxx alloy design