Momir Drakulic

Mr. Momir Drakulic

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 May 2022 in International Journal of Thermal Sciences
Verified
Journal Article
Closed access
WAWalid Boukera Abaci
Walid Boukera Abaci
NHNebojsa Hristov
Nebojsa Hristov
NANabil Ziane Ahmed
Nabil Ziane Ahmed
DJDamir D Jerković
Damir D Jerković
MDMomir Drakulic
Momir Drakulic

25 July 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
ABAbdeselem Benmeddah
Abdeselem Benmeddah
VJVesna Jovanović
Vesna Jovanović
SPSreten Radovan Peric
Sreten Radovan Peric
MDMomir Drakulic
Momir Drakulic
ADAleksandar Slobodan Djuric
Aleksandar Slobodan Djuric
DMDragan Marinkovic
Dragan Marinkovic
In the automotive sector, the use of multi-body software for modeling of existing vehicles has become essential due to its advantages in understanding vehicle dynamics in different situations and improving vehicle performances. This paper aims to model an off-road truck (4 × 4) by using ADAMS software 2020. Several steps must be achieved, including experimentally identifying some truck characteristics such as the mass, center of gravity coordinates, and tire vertical stiffness. The truck features leaf springs in both the front and rear suspensions, which must be validated before their integration into the full model due to their modeling complexity. This validation is performed by comparing the force–displacement characteristics obtained experimentally with simulation results from ADAMS, showing a good agreement. Then, the full truck is modeled in ADAMS software and validated through an experimental test using a repeated double-lane change scenario with two tests for the validation of the truck’s lateral dynamics. The comparison between the results shows a good correlation, validating the multi-body truck model.

1 July 2025 in Measurement
Verified
Journal Article
Closed access
MDMomir Drakulic
Momir Drakulic
SPSreten Radovan Peric
Sreten Radovan Peric
ADAleksandar Slobodan Djuric
Aleksandar Slobodan Djuric
SRSlavko Rakic
Slavko Rakic

1 January 2024 in Vojnotehnicki glasnik
Verified
Journal Article
Open access
PDF file
ABAbdeselem Benmeddah
Abdeselem Benmeddah
MDMomir Drakulic
Momir Drakulic
ADAleksandar Slobodan Djuric
Aleksandar Slobodan Djuric
SPSreten Radovan Peric
Sreten Radovan Peric
ABAleksandar G. Bukvić
Aleksandar G. Bukvić
AFAbdellah B. Ferfouri
Abdellah B. Ferfouri
Introduction/purpose: The study of vehicle suspension is a challenge for researchers in the field of vehicles regarding the impact of the suspension system on vehicle performances such as ride comfort, road holding, and working space. This paper presents the simulation of the Land Rover Defender 110 vehicle in the roll plane (half vehicle) in Simulink/MATLAB. The obtained results were compared with the results obtained in the ADAMS/CAR software package of the Land Rover Defender 110 simulation model previously experimentally validated. The Defender 110 vehicle has a dependent suspension system in both axles and a passive suspension type with four degrees of freedom (4 DOF). Methods: The equations of the system can be solved mathematically with a scheme in Simulink/MATLAB while half-vehicle modeling has been done in ADAMS/CAR. Results: The comparison of the vehicle characteristics obtained by the two simulation methods was done for three different scenarios, and it was noticed that there is a good correlation between them. Conclusion: It was concluded that the Defender 110 vehicle simulation model in Simulink/MATLAB is validated. The validated model can be used to perform suspension system optimization in future work.

1 January 2023 in Vojnotehnicki glasnik
Verified
Journal Article
Open access
PDF file
MDMomir Drakulic
Momir Drakulic
ADAleksandar Slobodan Djuric
Aleksandar Slobodan Djuric
LPLuka M. Ponorac
Luka M. Ponorac
ABAbdeselem Benmeddah
Abdeselem Benmeddah
SPSreten Radovan Peric
Sreten Radovan Peric
Introduction/purpose: The hydraulic buffering valve has the greatest influence on the dynamic characteristics of power-shift transmission. The hydraulic buffering valve is a transmission element that controls increase in pressure in friction assemblies during the gear shifting process. By choosing the optimal control of pressure increase during shifting, reduction of dynamic loads in gear transmissions and thermal loads in friction assemblies is achieved. Methods: The paper analyzes the principle of one of hydraulic buffering valve solutions as well as the influence of certain parameters on the control of pressure increase. After the analysis of the working principle of the hydraulic buffering valve, a simulation model was developed in the MATLAB/Simulink software package. Results: The results obtained using the simulation model were compared with the experimental results of the selected pressure modulator solution. The selected hydraulic buffering valve was developed as part of the development of a device for power-shift transmission. The simulation results showed a satisfactory match with the experimental results. Conclusion: The developed simulation model enables a relatively easy and quick change of the parameters of the hydraulic buffering valve as well as a possibility of a faster and better understanding of the influence of individual parameters on pressure increase during the gear shifting process.

1 January 2026
Verified
Conference Paper
Closed access
PDF file
MDMomir Drakulic
Momir Drakulic
ADAleksandar Slobodan Djuric
Aleksandar Slobodan Djuric
This paper presents a methodology for calculating interaction forces acting on the tracked armoured vehicle M-84 during motion on deformable terrain. The research is based on a previously developed and experimentally validated track-terrain interaction model, which is extended toward application at the vehicle level. The proposed approach applies a shear stress model within the framework of terramechanics theory to estimate the distribution of stresses along the track-soil contact area. Based on this model, the resultant interaction forces are numerically evaluated under different operating conditions, including straight motion and steering. The calculated force outputs are structured for integration into a complete dynamic vehicle model. They also provide a consistent input set for driveline analysis and transmission studies, especially for optimization of the gear shifting process in a power-shift transmission system, aiming to achieve smooth gear transitions without interruption of power flow. The presented methodology contributes to improved prediction of mobility performance and supports further development of control-oriented models of tracked armoured vehicles.