In the automotive sector, the use of multi-body software for modeling of existing vehicles has become essential due to its advantages in understanding vehicle dynamics in different situations and improving vehicle performances. This paper aims to model an off-road truck (4 × 4) by using ADAMS software 2020. Several steps must be achieved, including experimentally identifying some truck characteristics such as the mass, center of gravity coordinates, and tire vertical stiffness. The truck features leaf springs in both the front and rear suspensions, which must be validated before their integration into the full model due to their modeling complexity. This validation is performed by comparing the force–displacement characteristics obtained experimentally with simulation results from ADAMS, showing a good agreement. Then, the full truck is modeled in ADAMS software and validated through an experimental test using a repeated double-lane change scenario with two tests for the validation of the truck’s lateral dynamics. The comparison between the results shows a good correlation, validating the multi-body truck model.
Introduction/purpose: The study of vehicle suspension is a challenge for researchers in the field of vehicles regarding the impact of the suspension system on vehicle performances such as ride comfort, road holding, and working space. This paper presents the simulation of the Land Rover Defender 110 vehicle in the roll plane (half vehicle) in Simulink/MATLAB. The obtained results were compared with the results obtained in the ADAMS/CAR software package of the Land Rover Defender 110 simulation model previously experimentally validated. The Defender 110 vehicle has a dependent suspension system in both axles and a passive suspension type with four degrees of freedom (4 DOF). Methods: The equations of the system can be solved mathematically with a scheme in Simulink/MATLAB while half-vehicle modeling has been done in ADAMS/CAR. Results: The comparison of the vehicle characteristics obtained by the two simulation methods was done for three different scenarios, and it was noticed that there is a good correlation between them. Conclusion: It was concluded that the Defender 110 vehicle simulation model in Simulink/MATLAB is validated. The validated model can be used to perform suspension system optimization in future work.
30 March 2017 in Studia Universitatis Babeș-Bolyai Chemia
Biogas production by anaerobic digestion of residual waters from different sources (a treatment plant and a beer factory) was investigated in laboratory small scale batch reactors. Both wastewaters represent efficient biogas substrates. As concern the methane composition, the value is slightly higher in the case of biogas produced by anaerobic digestion of wastewater from beer factory. In the second part of this study, anaerobic co-digestion of wastewater and cow whey was performed. Addition of cow whey to wastewater from beer factory increase the biogas yield, while the addition of cow whey to wastewater from treatment plant decrease the biogas yield. In both cases of co-digestion, the methane content in biogas was higher than in the single digestion processes.
Introduction/purpose: The hydraulic buffering valve has the greatest influence on the dynamic characteristics of power-shift transmission. The hydraulic buffering valve is a transmission element that controls increase in pressure in friction assemblies during the gear shifting process. By choosing the optimal control of pressure increase during shifting, reduction of dynamic loads in gear transmissions and thermal loads in friction assemblies is achieved. Methods: The paper analyzes the principle of one of hydraulic buffering valve solutions as well as the influence of certain parameters on the control of pressure increase. After the analysis of the working principle of the hydraulic buffering valve, a simulation model was developed in the MATLAB/Simulink software package. Results: The results obtained using the simulation model were compared with the experimental results of the selected pressure modulator solution. The selected hydraulic buffering valve was developed as part of the development of a device for power-shift transmission. The simulation results showed a satisfactory match with the experimental results. Conclusion: The developed simulation model enables a relatively easy and quick change of the parameters of the hydraulic buffering valve as well as a possibility of a faster and better understanding of the influence of individual parameters on pressure increase during the gear shifting process.
This paper presents only a part of the risks and harmfulness to which the employees working in Serbian MoD and especially in Technical Test Center are exposed during tests on new armaments and various other equipment under development. In addition to the results of noise and vibration measurements in the working environment at the training grounds and the airport, the risks during laboratory and experimental-exploitation tests in the field are presented. Noise and vibration as harmfulness effects were measured and evaluated according to the relevant criteria, while far more dangerous risks of working with prototypes are immeasurable, unpredictable and not included in the regulations.