Abdeselem Benmeddah

Mr. Abdeselem Benmeddah

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 July 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
ABAbdeselem Benmeddah
Abdeselem Benmeddah
VJVesna Jovanović
Vesna Jovanović
SPSreten Radovan Peric
Sreten Radovan Peric
MDMomir Drakulic
Momir Drakulic
ADAleksandar Slobodan Djuric
Aleksandar Slobodan Djuric
DMDragan Marinkovic
Dragan Marinkovic
In the automotive sector, the use of multi-body software for modeling of existing vehicles has become essential due to its advantages in understanding vehicle dynamics in different situations and improving vehicle performances. This paper aims to model an off-road truck (4 × 4) by using ADAMS software 2020. Several steps must be achieved, including experimentally identifying some truck characteristics such as the mass, center of gravity coordinates, and tire vertical stiffness. The truck features leaf springs in both the front and rear suspensions, which must be validated before their integration into the full model due to their modeling complexity. This validation is performed by comparing the force–displacement characteristics obtained experimentally with simulation results from ADAMS, showing a good agreement. Then, the full truck is modeled in ADAMS software and validated through an experimental test using a repeated double-lane change scenario with two tests for the validation of the truck’s lateral dynamics. The comparison between the results shows a good correlation, validating the multi-body truck model.

1 January 2024 in Vojnotehnicki glasnik
Verified
Journal Article
Open access
PDF file
ABAbdeselem Benmeddah
Abdeselem Benmeddah
MDMomir Drakulic
Momir Drakulic
ADAleksandar Slobodan Djuric
Aleksandar Slobodan Djuric
SPSreten Radovan Peric
Sreten Radovan Peric
ABAleksandar G. Bukvić
Aleksandar G. Bukvić
AFAbdellah B. Ferfouri
Abdellah B. Ferfouri
Introduction/purpose: The study of vehicle suspension is a challenge for researchers in the field of vehicles regarding the impact of the suspension system on vehicle performances such as ride comfort, road holding, and working space. This paper presents the simulation of the Land Rover Defender 110 vehicle in the roll plane (half vehicle) in Simulink/MATLAB. The obtained results were compared with the results obtained in the ADAMS/CAR software package of the Land Rover Defender 110 simulation model previously experimentally validated. The Defender 110 vehicle has a dependent suspension system in both axles and a passive suspension type with four degrees of freedom (4 DOF). Methods: The equations of the system can be solved mathematically with a scheme in Simulink/MATLAB while half-vehicle modeling has been done in ADAMS/CAR. Results: The comparison of the vehicle characteristics obtained by the two simulation methods was done for three different scenarios, and it was noticed that there is a good correlation between them. Conclusion: It was concluded that the Defender 110 vehicle simulation model in Simulink/MATLAB is validated. The validated model can be used to perform suspension system optimization in future work.

1 January 2023 in Scientific Technical Review
Verified
Journal Article
Open access
PDF file
TAToufik Allouche
Toufik Allouche
AFAbdellah Ferfouri
Abdellah Ferfouri
NHNebojša Hristov
Nebojša Hristov
DJDamir D Jerković
Damir D Jerković
MSMarijana Stalević
Marijana Stalević
ABAleksandar G. Bukvić
Aleksandar G. Bukvić
Measurements of recoil and counter-recoil movement in weapons are essential in order to optimize ballistic performances, to ensure safety during firing, to improve the accuracy and the effectiveness of the weapon during its life cycle and to guide design and development work. From this, the present work focuses on contact-based measurements of the counter-recoil movement of the D30J 122 mm howitzer using two inductive sensors, namely, displacement sensor and acceleration sensor. The measurements from the displacement sensor were used to calculate the velocity and acceleration of the counter-recoil by derivation and those of the acceleration sensors were used to calculate the velocity and displacement of the counter-recoil by integration. The comparison between the measured and calculated results obtained from the two sensors shows a very good similarity in form of variation and in values, which validates the applied experimental approach in this work and confirms the accuracy of both measurement methods.

1 January 2023 in Vojnotehnicki glasnik
Verified
Journal Article
Open access
PDF file
MDMomir Drakulic
Momir Drakulic
ADAleksandar Slobodan Djuric
Aleksandar Slobodan Djuric
LPLuka M. Ponorac
Luka M. Ponorac
ABAbdeselem Benmeddah
Abdeselem Benmeddah
SPSreten Radovan Peric
Sreten Radovan Peric
Introduction/purpose: The hydraulic buffering valve has the greatest influence on the dynamic characteristics of power-shift transmission. The hydraulic buffering valve is a transmission element that controls increase in pressure in friction assemblies during the gear shifting process. By choosing the optimal control of pressure increase during shifting, reduction of dynamic loads in gear transmissions and thermal loads in friction assemblies is achieved. Methods: The paper analyzes the principle of one of hydraulic buffering valve solutions as well as the influence of certain parameters on the control of pressure increase. After the analysis of the working principle of the hydraulic buffering valve, a simulation model was developed in the MATLAB/Simulink software package. Results: The results obtained using the simulation model were compared with the experimental results of the selected pressure modulator solution. The selected hydraulic buffering valve was developed as part of the development of a device for power-shift transmission. The simulation results showed a satisfactory match with the experimental results. Conclusion: The developed simulation model enables a relatively easy and quick change of the parameters of the hydraulic buffering valve as well as a possibility of a faster and better understanding of the influence of individual parameters on pressure increase during the gear shifting process.