Using adhesives for connection technology has many benefits. It is cost-efficient, fast, and allows homogeneous stress distribution between the bonded surfaces. This paper gives an overview on the current state of knowledge regarding the technologically important area of adhesive materials, as well as on emergent related technologies. It is expected to fill some of the technological gaps between the existing literature and industrial reality, by focusing at opportunities and challenges in the adhesives sector, on sustainable and eco-friendly chemistries that enable bio-derived adhesives, recycling and debonding, as well as giving a brief overview on the surface treatment approaches involved in the adhesive application process, with major focus on metal and polymer matrix composites. Finally, some thoughts on the connection between research and development (R&D) efforts, industry standards and regulatory aspects are given. It contributes to bridge the gap between industry and research institutes/academy. Examples from the aeronautics industry are often used since many technological advances in this industry are innovation precursors for other industries. This paper is mainly addressed to chemists, materials scientists, materials engineers, and decision-makers.

There is a strong need to develop and implement appropriate alternatives to replace formaldehyde-based adhesive systems, such as phenol–formaldehyde, in the industry of wood-based panels (WBPs). This is due to the toxicity and volatility of formaldehyde and restrictions on its use associated with some formaldehyde-based adhesives. Additionally, the current pressure to reduce the dependence on polymeric materials, including adhesives, from petrochemical-based sources has led to increased interest in bio-based adhesives, which, in some cases, already provide acceptable properties to the end-product. Among the potential raw materials for good-quality, renewable-based adhesive formulations, this paper highlights tannins, lignin, and protein sources. However, regarding renewable sources, specific features must be considered, such as their lower reactivity than certain petrochemical-based sources and, therefore, higher production costs, resource availability issues, and the need for toxicological investigations on alternative systems, to compare them to conventional systems. As a result, further research is highly encouraged to develop viable formaldehyde-free adhesive systems based on renewable sources, either at the technical or economical level. Moreover, herein, we also showcase the present market of WBPs, highlighting the obstacles that the alternative and new bio-based adhesives must overcome.

Polylactic acid (PLA) has been used as a matrix material to produce composites with natural fibers, which present several advantages, being one of them the addition of value to agricultural waste. Thus, this study aims to develop a PLA 3D filament with the incorporation of a waste agriculture product (rice husk (RH)). For that, RH fibers were prepared, and PLA was loaded up to 20% RH. The filaments were obtained by extrusion. Finally, samples were produced by fused deposition modeling (FDM). The fibers and filaments’ density and thermal stability (TGA) were determined, and their chemical structure changes due to alkali treatment were accessed by Fourier Transform Infrared Spectroscopy (FTIR). Printability tests were performed, and printed samples were characterized in terms of density, water absorption, and mechanical behavior (compression, tensile, and flexural tests). The results showed that the alkali treatment changed the chemical structure of RH fibers and TGA showed that the filaments did not degrade significantly until 250ºC. The best printability was achieved with 5% of HR content and was the one that showed the lowest mechanical properties reduction. Overall, the present work showed that RH fibers can be successfully used as a filler in PLA filaments for FDM.

For the past two decades, with the increase in plastic consumption came a rise in plastic waste, with the bulk of it ending up in landfills, incinerated, recycled or leaking into the environment, especially in aquatic ecosystems. Plastic waste poses a significant environmental threat and a wealth issue due to its non-biodegradability and recalcitrant nature. Polyethylene (PE) remains one of the major utilized polymers in different applications amid all the other types because of its low production costs, simplistic nature prone to be modified and historically predominant researched material. Since the common methods for plastic disposal are troubled by limitations, there is a growing need for more appropriate and environment friendly methods alternatives. This study highlights several ways that can be used to assist PE (bio)degradation and mitigate its waste impact. Biodegradation (microbiological activity driven) and photodegradation (radiation driven) are the most promising for PE waste control. The shape of the material (powder, film, particles, etc.), the composition of medium, additives and pH, temperature and incubation or exposure times contribute to plastic degradation efficiency. Moreover, radiation pretreatment can enhance the biodegradability of PE, providing a promising approach to fighting plastic pollution. This paper relates the most significant results regarding PE degradation studies followed by weight loss analysis, surface morphology changes, oxidation degree (for photodegradation) and mechanical properties assessment. All combined strategies are very promising to minimize the polyethylene impact. However, there is still a long way to go through. The degradation kinetics is still low for the currently available biotic or abiotic processes, and complete mineralization is thoroughly unseen.