Vegetable-oil-based biolubricants are an excellent alternative to conventional lubricants. Instead of focusing on novel feedstocks, these biolubricants should be further elucidated based on their fatty acid composition, which influences their tribological properties. Therefore, the study utilises gene expression programming (GEP) to derive a boundary lubricity model for vegetable-oil-derived trimethylolpropane (TMP) esters, considering the fatty acid composition (saturation and monounsaturation levels), load and speed. Neat vegetable oil and blends from seven feedstocks are selected following a wide range of fatty acid profiles to synthesise TMP esters using a two-stage transesterification process. The TMP esters are spin-coated on wear discs that are subsequently rotated against a ball using a purpose-built tribometer. The frictional performance of the TMP esters with balanced saturation and monounsaturation levels of fatty acid are measured to improve it at higher speeds. The GEP model is statistically evaluated by adopting the friction data, a showing good generalisation and predictability capability. The model demonstrates that friction decreases with increasing saturation levels of the TMP ester. The GEP model for vegetable oil TMP esters allows for the tribological performance prediction of TMP esters following the fatty acid profile, providing a platform to optimise such biolubricant for desired applications.
1 August 2025 in Journal of Traffic and Transportation Engineering (English Edition)
Within electrical contacts, poor electrical conductivity of lubricants can lead to triboelectric charging, causing electrostatic currents and thermal effects, which accelerate lubrication failure. This study aimed to address these challenges by producing and testing three greases with different base oils: ionic liquid ([Oley][Oleic]), synthetic oil (PAO4), and vegetable oil-based synthetic ester (trimethylolpropane oleate). Each grease was prepared with polytetrafluoroethylene powder as the thickener. The greases were tested using a custom-made tribometer, integrated with a grounded electrical current system, with friction tests conducted with up to a 2 A electrical current flow at a constant voltage supply of 4.5 V. Under triboelectric friction testing, [Oley][Oleic] grease outperformed a commercial perfluoropolyether grease by 27.7% in friction and 16.3% in wear. This grease also showed better performance than formulated lithium grease with extreme pressure additives. The study demonstrates that greases with low interfacial resistance can retain their lubrication capacity under triboelectric conditions. These results indicate that [Oley][Oleic] grease, with its ionic liquid base oil, offers a promising solution for applications involving electrical contacts. This study highlights the potential of using advanced base oils and thickeners to enhance the performance and sustainability of lubricants in demanding environments.
PEDOT:PSS is a conducting organic polymer widely studied for a transparent conductive electrode. The conventional method to fabricate PEDOT:PSS thin film involves a post-treatment process entailing dipping into strong and toxic saturated acid to enhance the film’s conductivity. Eliminating the post-treatment process reduces excess strong saturated acid or solvent waste, shortening the fabricating time by half. Therefore, this study presents a quick and facile solution-processed method for fabricating the PEDOT:PSS transparent conductive thin film (without a post-treatment process) while still achieving the requirements for a transparent conductive electrode (TCE). A parametric study was conducted by adding 5 wt% to 80 wt% of benzene sulfonic acid (BA) to PEDOT:PSS during the formulation stage before being dried at elevated temperatures from 80 °C to 200 °C. The optimum sheet resistance and transmittance value could be achieved for a thin film fabricated from PEDOT:PSS added with 40 wt% of BA, and dried at 120 °C. The sheet resistance and transmittance values are 80 ?/sq and 93.6%, respectively. The generated figure of merit (FOM) value is 70.1, indicating an improvement of almost five times compared to the FOM value of 14.6 generated using the conventional method, requiring a post-treatment process. ABSTRAK: PEDOT:PSS adalah bahan polimer organik yang mengkonduksi arus dan dikaji secara meluas bagi digunakan sebagai elektrod konduktif telus. Kaedah konvensional untuk menghasilkan filem nipis PEDOT:PSS melibatkan proses pasca rawatan iaitu dengan mencelupkan filem nipis PEDOT:PSS ke dalam asid pekat bertoksik bagi meningkatkan konduksi filem tersebut. Tanpa proses pasca rawatan ini dapat mengurangkan penghasilan sisa lebihan seperti asid pekat bertoksik atau pelarut buangan, memendekkan masa fabrikasi sebanyak separuh. Oleh itu, kajian ini menghasilkan kaedah proses-penyelesaian yang cepat dan mudah bagi fabrikasi filem nipis PEDOT:PSS (tanpa proses pasca rawatan) disamping masih mencapai keperluan sebagai elektrod konduktif telus (TCE). Kajian parametrik telah dijalankan dengan menambah 5 wt% hingga 80 wt% asid sulfonik benzena (BA) ke dalam PEDOT:PSS pada peringkat percampuran kimia sebelum dikeringkan pada kenaikan suhu secara berperingkat dari 80 °C sehingga 200 °C. Nilai optimum bagi rintangan lapisan dan nilai ketelusan bagi filem nipis PEDOT:PSS yang difabrikasi dapat dicapai melalui penambahan sebanyak 40 wt% BA dan dikeringkan pada suhu 120 °C. Rintangan lapisan dan nilai ketelusan telah dicapai sebanyak 80 ?/sq dan 93.6%, masing-masing. Nilai gambaran merit (FOM) yang terhasil adalah 70.1, menunjukkan peningkatan hampir lima kali ganda berbanding nilai FOM 14.6 yang terhasil menggunakan kaedah konvensional yang memerlukan proses pasca-rawatan.