Jiangying Xiong

Dr. Jiangying Xiong


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 August 2024 in Materials
Verified
Journal Article
Open access
PDF file
JXJiangying Xiong
Jiangying Xiong
CYChao Yin
Chao Yin
CWChong Wang
Chong Wang
GFGanjiang Feng
Ganjiang Feng
JGJianzheng Guo
Jianzheng Guo
This study investigates the microstructural evolution and its effect on the fatigue performance of a novel nickel-based powder superalloy FGH4113A (WZ-A3) after long-term aging at 760 °C and 815 °C. The results show that long-term aging both at 760 °C and 815 °C has no significant effect on the grain size and morphology of the alloy. After aging at 760 °C for up to 2020 h, the size of the γ′ phase remains unchanged, and its morphology transitions from nearly square to nearly spherical. During long-term aging at 815 °C for 440 h, γ′ phase coarsening and spheroidizing occur simultaneously. With prolonged aging time, the size and spheroidization degree of the γ′ phase further increase. During long-term aging up to 440 h at 760 °C, the dispersed granular MC and M6C carbides dissolve and re-precipitate. By 2020 h of aging, flocculent carbides precipitate and non-continuous M6C and M23C6 accumulate at grain boundaries. After long-term aging at 815 °C for 440 h, flocculent carbides begin to precipitate within the grains. By 2020 h of aging, a large amount of flocculent carbides precipitate with significant coarsening and enrichment of the grain boundary carbides. Due to the insignificant coarsening of the γ′ phase as well as the enrichment and precipitation of the grain boundary carbides, the fatigue performance of the alloy decreases slightly after long-term aging.

25 February 2025 in Materials
Verified
Journal Article
Open access
PDF file
JXJiangying Xiong
Jiangying Xiong
CYChao Yin
Chao Yin
ALAnping Long
Anping Long
JCJunyi Cheng
Junyi Cheng
GFGanjiang Feng
Ganjiang Feng
JGJianzheng Guo
Jianzheng Guo
A novel nickel-based powder metallurgy superalloy was processed using two different thermal–mechanical processes, including hot isostatic pressed (As-HIP) and hipped + hot extruded + isothermally-forged (IF) heat treatments following two processed alloys, designated as As-HIP-HT and IF-HT. The objective of this study is to investigate the microstructure and mechanical property evolution in a nickel-based powder disk alloy fabricated by two processes. The findings revealed that both As-HIP and IF alloys underwent substantial recrystallization, with grains in the IF alloy being finer. Notable Prior Particle Boundaries (PPBs) were identified in the As-HIP samples. The IF-HT alloy exhibited a larger grain size due to a greater amount of stored energy. Significant differences in the secondary γ′ precipitates were observed between the two processes. More uniform substructures in the IF-HT alloy led to a higher density of finer γ′ precipitates. At temperatures of 704 °C and 760 °C, the As-HIP-HT alloy displayed a higher yield strength, but its plasticity significantly declined as temperature increased, while the IF-HT alloy showed a relatively stable plasticity. The presence of PPBs in the As-HIP-HT alloy minimally affected the alloy’s strength but reduced its plasticity. The creep property of the two processes was compared at 800 °C/330 MPa; the IF-HT alloy demonstrated lower creep rates and a longer creep life, which was attributed to its finer γ′ precipitates. Dominant creep deformation mechanisms in the As-HIP-HT alloy included Orowan dislocation loops and deformation twinning, while the primary mechanisms in the IF-HT alloy involved dislocation cutting through γ′ precipitates, dislocation slip, and micro-twins. These findings support the use of isostatic pressing + hot extrusion+ isothermally-forging process for critical high-temperature components.