Transition Edge Sensors (TESs) are amongst the most sensitive cryogenic detectors and can be easily optimized for the detection of massive particles or photons ranging from X-rays all the way down to millimetre radiation. Furthermore, TESs exhibit unmatched energy resolution while being easily frequency domain multiplexed in arrays of several hundred pixels. Such great performance, along with rather simple and sturdy readout and amplification chains make TESs extremely compelling for applications in many fields of scientific endeavour. While the first part of this article is an in-depth discussion on the working principles of Transition Edge Sensors, the remainder of this review article focuses on the applications of Transition Edge Sensors in advanced scientific instrumentation serving as an accessible and thorough list of possible starting points for more comprehensive literature research.
15 November 2022 in Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
We present the characterization of a prototype TES bolometer suitable for Cosmic Microwave Background (CMB) measurements. This detector consists of a double layer (Ti-Au) superconducting film thermally coupled to a large area (8 mm diameter) spiderweb absorber, fabricated at INFN Genova. Thermo-electrical properties of the superconducting film are measured by means of four-wires and two-wire setups. These include Resistance vs Temperature curve, which allows us to determine the critical temperature, other parameters of the transition, and the critical current. From the measurement of the critical retrapping current, we can estimate the thermal conductance ($G$) of the device. TES properties are also measured by reading it out through a SQUID amplifier. This allows us to measure the current-voltage curve (I-V) and saturation power ($P_{sat}$). A second, independent, estimate of $G$ is obtained by measuring $P_{sat}$ at different thermal bath temperatures, which agrees with the first one. Furthermore, a red LED, installed in the cryogenic environment, illuminates the detector absorber, while operating the bolometer in negative electrothermal feedback. We investigate the bolometric and calorimetric regime of the device using a slow modulated LED signal for the former and a fast (compared to the expected detector time constant) pulsed signal for the latter. The bolometer time constant ($\tau$) is extracted by using this method. To study the behavior of the device in the presence of cosmic rays background, and to achieve a further estimation of $\tau$, we expose the bolometer to a $^{214}$Am alpha source.
7 May 2026 in IEEE Transactions on Applied Superconductivity
The LiteBIRD satellite will map the polarisation of the Cosmic Microwave Background (CMB) with unprecedented sensitivity by means of antenna-coupled transition edge sensors (TESs). Its current design features single SQUID-Array Amplifiers (SAA) at a temperature of about 400 mK in order to read out up to 64 TESs in a frequency division multiplexing scheme. The front-end part of the electronics (the SQUID Controller Assembly -SCA) was designed to handle this configuration. Nevertheless, alternative configurations of the experiment are being studied that might require a dual-stage SQUID (DSS) amplification chain in order to meet thermal and noise requirements. In light of this possibility, we have successfully investigated the feasibility of controlling two individual SAAs in a DSS Amplifier (DSSA) configuration with two independent channels of the present SCA. The SQUID directly connected to the sensor, commonly referred to as ‘front-end’, behaves as an emitter-follower, or buffer, circuit and it decouples the impedance of the TES(s) from the rest of the readout chain whilst producing a moderate amplification. The second SQUID, ‘booster’, is responsible for a high-gain amplification of the signal and can be thermally decoupled from the front-end allowing it to dissipate a lot more power and thus exhibiting a higher gain. We characterised a breadboard model in which two SQUID amplifiers are cascaded but hosted on the same circuit board and thus not thermally decoupled. This was intended to perform functional tests and to assess the feasibility of controlling a DSSA without introducing major changes in the already developed LiteBIRD SCA. We present the typical I-V and I-$\Phi$ curves of the two SQUIDs along with the characterisation of the DSSA in terms of bandwidth, linearity and total harmonic distortion (THD).
20 April 2026 in IEEE Transactions on Applied Superconductivity
The new generation of Cosmic Microwave Background (CMB) experiments exploits the properties of low-temperature detectors, particularly superconducting Transition Edge Sensor (TES) bolometers, whose characteristics make them ideal for present and future CMB measurements. Frequency Domain Multiplexing (FDM) configuration is performed by connecting an LC filter in series with each TES. The presence of the LC filters and the SQUID input coil and wiring in series with all the LC channels cause systematic electrical crosstalk.In this work we present the tests and characterization performed on an LC chip produced by SRON (Space Research Organization Netherlands) for the experiment SWIPE. These LC chips are composed of lithographically fabricated inductors and by parallel plate capacitors. The measurements were focused on retrieving the resonance frequencies to be compared to the expected design values, the quality factor and the parasitic resistance. The results were consistent with previous measurements performed on similar setups, showing Q-factors above $\mathbf {10^{4}}$ and parasitic resistance on the order of $\mathbf {10^{-2}\;\Omega }$. The dependence of the properties of the LC filters and the SQUID on the temperature and the bias settings was studied. Measurements to define the level and the major contributors to electrical crosstalk were performed. Both modeling and experimental results indicated an electrical crosstalk level on the order of 10-4.