Su-Wan Choi

Mr. Su-Wan Choi

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 October 2025 in Combustion and Flame
Verified
Journal Article
Closed access
KLKeon-Hyeong Lee
Keon-Hyeong Lee
BSBu-Kyeng Sung
Bu-Kyeng Sung
GMGyeong-Ui Mo
Gyeong-Ui Mo
SCSu-Wan Choi
Su-Wan Choi
MJMin-Seon Jo
Min-Seon Jo
Jeong-Yeol ChoiJeong-Yeol Choi
Jeong-Yeol Choi

1 March 2026 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
SJSeunghyun Jo
Seunghyun Jo
SCSu-Wan Choi
Su-Wan Choi
GMGyeong-Ui Mo
Gyeong-Ui Mo
WHWoo-Seok Han
Woo-Seok Han
BSBu-Kyeng Sung
Bu-Kyeng Sung
Jeong-Yeol ChoiJeong-Yeol Choi
Jeong-Yeol Choi
The present work has experimentally studied the effects of chamber length on flow fields of detonation waves in a non-premixed ethylene-oxygen rotating detonation engine (RDE). RDEs are constant-volume combustion devices offering higher performance than constant-pressure engines, with shorter chamber lengths that reduce weight and size, thereby improving efficiency. A comprehensive physical explanation for the stability and performance in RDEs at varied chamber lengths remains elusive. Experiments are performed at chamber lengths (30, 45, 60, 75, and 90 mm) and under a constant flow condition. Detonation waves are captured through a visible chamber wall and the RDE exit using two high-speed cameras simultaneously. Thrust and chamber pressure are measured to assess the performance of the RDE. Stable detonation wave cycles are observed at chamber lengths of 30 and 45 mm. At 60, 75, and 90 mm, the detonation waves demonstrate instability. This instability is attributed to interactions between combustion products from the previous cycle and an oblique shock in the current cycle, which may result in detonation quenching. The detonation wave speeds are reported as follows: 1414 m/s at the chamber length of 30 mm, and 1327 m/s at 90 mm. Pressure efficiency remains nearly uniform at 67%–69% for the chamber lengths of 45–90 mm, peaking at 76% for 30 mm. Thrust efficiency is consistently 79%–82% across the chamber lengths. The results provide insights into designing RDEs with an optimized chamber length, enabling stable detonation waves and minimizing detonation quenching, thereby improving RDE efficiency.

13 September 2024 in Aerospace
Verified
Journal Article
Open access
PDF file
GMGYEONG-UI MO
GYEONG-UI MO
IKIn-Hoi Koo
In-Hoi Koo
KLKeon-Hyeong Lee
Keon-Hyeong Lee
SCSu-Wan Choi
Su-Wan Choi
Jeong-Yeol ChoiJeong-Yeol Choi
Jeong-Yeol Choi
This study investigates the operational characteristics of the Rotating Detonation Engine (RDE), with a focus on fuel injector design. Inspired by the similarity between the fuel injection structure of RDE and the Jet in Supersonic Crossflow (JISC) of a scramjet, experimental research on fuel injectors with jet penetration was conducted. Five injectors were designed, each with a fixed fuel injection area or injection hole diameter. Experiments determined practical injection areas, and an empirical correlation was used to calculate jet penetration heights. Under conditions of a total mass flow rate of 105 ± 5 g/s and an equivalence ratio of 1.05 ± 0.1, combustion modes were analyzed. Initial detonation occurrence was assessed through pressure history, with a detailed analysis via image post-processing. The results indicated that the injector D4N15, with the highest jet penetration height, exhibited deflagration, while D4N23 showed chaotic propagation. The injector D2N60 demonstrated relatively unstable behavior in sustained detonation cases. Thrust comparisons revealed that D4N30, with wider hole spacing and higher jet penetration height, exhibited approximately 12.5% higher specific impulse compared to D1N240. These outcomes confirm the significant impact of jet penetration height and hole spacing on detonation propagation and engine performance.

27 August 2025 in Aerospace
Verified
Journal Article
Open access
PDF file
SCSu-Wan Choi
Su-Wan Choi
SJSeunghyun Jo
Seunghyun Jo
BSBu-Kyeng Sung
Bu-Kyeng Sung
JKJaeeun Kim
Jaeeun Kim
KLKeon-Hyeong Lee
Keon-Hyeong Lee
Jeong-Yeol ChoiJeong-Yeol Choi
Jeong-Yeol Choi
In this study, emissivity was employed as the primary metric for evaluating the radiative-cooling performance of a supersonic nozzle under flight-like conditions. A supersonic nozzle was fabricated by PBF, after which combustion (hot-fire) tests and emissivity measurements were carried out. These data enabled quantification and visualization of radiant energy in the 8–14 µm-wavelength band during combustion. The hot-fire tests revealed a clear cap-shock pattern, confirming that the nozzle flow was fully developed. Emissivity measurements showed that the additively manufactured surface—subsequently treated by the AMS 5662 heat-treatment process—followed the angular-emission trends reported in previous studies. The surface exhibited a high roughness (Ra ≈ 30 µm) and an emissivity of 0.85 in the 8–14 µm band; a temperature-dependent emissivity fitting function was accordingly derived. By coupling the combustion test results with the emissivity data, the actual temperature distribution along the nozzle surface and the corresponding radiant energy in the 8–14 µm band were quantitatively reconstructed and visualized. The maximum emissive power in this band reached 2214 W m−2, representing at least 16.61% of the total black-body radiation at 700 K.

20 October 2026 in Proceedings of the Combustion Institute
Verified
Journal Article
Closed access
KLKeon-Hyeong Lee
Keon-Hyeong Lee
SCSu-Wan Choi
Su-Wan Choi
GMGyeong-Ui Mo
Gyeong-Ui Mo
WHWoo-Seok Han
Woo-Seok Han
BSBu-Kyeng Sung
Bu-Kyeng Sung
Jeong-Yeol ChoiJeong-Yeol Choi
Jeong-Yeol Choi