In-Hoi Koo

Mr. In-Hoi Koo


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 November 2023 in Aerospace
Verified
Journal Article
Open access
PDF file
IKIn-Hoi Koo
In-Hoi Koo
KLKeon-Hyeong Lee
Keon-Hyeong Lee
MKMinsu Kim
Minsu Kim
HHHyung-Seok Han
Hyung-Seok Han
HKHolak Kim
Holak Kim
Jeong-Yeol ChoiJeong-Yeol Choi
Jeong-Yeol Choi
Fuel injection and mixing affect the characteristics of detonation initiation and propagation, as well as the propulsion performance of rotating detonation engine (RDE). A study on the injector is carried out in the present investigation. A rectangular-shaped hole-type fuel injector (RHFI) and slit-type fuel injector (SFI) were designed and compared experimentally at equivalent conditions. The investigation of the detonation propagation modes and the analysis of propulsion performance were carried out using fast Fourier transform (FFT), short-time Fourier transform (STFT), and unwrapped image post-processing. Under 50, 75, and 100 g/s flow rate conditions at an equivalence ratio of 1.0 ± 0.05, the RHFI has relatively stable detonation propagation characteristics, higher thrust, and specific impulse performance. Additionally, the results of the experiment indicate that the number of detonation waves affects performance.

11 August 2023 in Aerospace
Verified
Journal Article
Open access
PDF file
MKMinsu Kim
Minsu Kim
IKIn-Hoi Koo
In-Hoi Koo
KLKeon-Hyeong Lee
Keon-Hyeong Lee
ELEun Sung Lee
Eun Sung Lee
HHHyung-Seok Han
Hyung-Seok Han
Jeong-Yeol ChoiJeong-Yeol Choi
Jeong-Yeol Choi
This experimental investigation focused on the ignition and combustion characteristics of a tandem cavity-based scramjet combustor with side-by-side identical cavities. This study utilized the Pusan National University-direct connect scramjet combustor (PNU-DCSC), which was capable of simulating flight conditions at Mach number 4.0–5.0 and altitudes of 20–25 km using the vitiated air heater (VAH). The combustion tests were conducted under off-design point conditions corresponding to low inlet enthalpy. It is a condition in which self-ignition does not occur, and a micro pulse detonation engine (μPDE) ignitor is used. The results revealed that as the injection pressure of the gaseous hydrogen fuel (GH2) and the corresponding equivalence ratio increased, the combustion mode transitioned from the cavity-shear layer flame to the jet-wake flame. Furthermore, the measured wall static pressure profiles along the isolator and scramjet combustor indicated that the region of elevated pressure distribution caused by the shock train expanded upstream with higher equivalence ratios. When ignited from the secondary cavity, the combustion area did not extend to the primary cavity at lower equivalence ratios, while it expanded upstream faster with higher equivalence ratios. Therefore, the combustion characteristics of the tandem cavity were found to vary based on the overall equivalence ratio of the main fuel (GH2) and ignition position.

13 September 2024 in Aerospace
Verified
Journal Article
Open access
PDF file
GMGYEONG-UI MO
GYEONG-UI MO
IKIn-Hoi Koo
In-Hoi Koo
KLKeon-Hyeong Lee
Keon-Hyeong Lee
SCSu-Wan Choi
Su-Wan Choi
Jeong-Yeol ChoiJeong-Yeol Choi
Jeong-Yeol Choi
This study investigates the operational characteristics of the Rotating Detonation Engine (RDE), with a focus on fuel injector design. Inspired by the similarity between the fuel injection structure of RDE and the Jet in Supersonic Crossflow (JISC) of a scramjet, experimental research on fuel injectors with jet penetration was conducted. Five injectors were designed, each with a fixed fuel injection area or injection hole diameter. Experiments determined practical injection areas, and an empirical correlation was used to calculate jet penetration heights. Under conditions of a total mass flow rate of 105 ± 5 g/s and an equivalence ratio of 1.05 ± 0.1, combustion modes were analyzed. Initial detonation occurrence was assessed through pressure history, with a detailed analysis via image post-processing. The results indicated that the injector D4N15, with the highest jet penetration height, exhibited deflagration, while D4N23 showed chaotic propagation. The injector D2N60 demonstrated relatively unstable behavior in sustained detonation cases. Thrust comparisons revealed that D4N30, with wider hole spacing and higher jet penetration height, exhibited approximately 12.5% higher specific impulse compared to D1N240. These outcomes confirm the significant impact of jet penetration height and hole spacing on detonation propagation and engine performance.