Sreeramulu Dowluru

Dr. Sreeramulu Dowluru

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 February 2024 in Journal of the Chinese Institute of Engineers
Verified
Journal Article
Closed access
SRSivasankara Raju Rallabandi
Sivasankara Raju Rallabandi
DPDevi Prasad Pilla
Devi Prasad Pilla
SDSreeramulu Dowluru
Sreeramulu Dowluru
SPSrihari Palli
Srihari Palli
NSNeeraj Sharma
Neeraj Sharma
RSRAKESH CHANDMAL SHARMA
RAKESH CHANDMAL SHARMA

3 November 2015 in Indian Journal of Science and Technology
Verified
Journal Article
Open access
PDF file
KRK. Ramarao
K. Ramarao
CRC. J. Rao
C. J. Rao
SDSreeramulu Dowluru
Sreeramulu Dowluru
The Experimental Investigation on Performance and Emission Characteristics of a Single Cylinder Diesel Engine using Nano Additives in Diesel and Biodiesel

1 January 2018 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
PDF file
DKD. Mohana Krishnudu
D. Mohana Krishnudu
SDSreeramulu Dowluru
Sreeramulu Dowluru
Pathapalli Venkateshwar ReddyPathapalli Venkateshwar Reddy
Pathapalli Venkateshwar Reddy
In the current study mechanical properties of particles filled hybrid composites have been studied. The mechanical properties of the hybrid composite mainly depend on the proportions of the coir weight, Luffa weight and filler weight. RSM along with Taguchi method have been applied to find the optimized parameters of the hybrid composites. From the current study it was observed that the tensile strength of the composite mainly depends on the coir percent than the other two particles.

1 September 2016 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
MRM Siva Eswara Rao
M Siva Eswara Rao
SDSreeramulu Dowluru
Sreeramulu Dowluru
DND Asiri Naidu
D Asiri Naidu
Nano fluids are used for increasing thermal properties in heat transfer equipment like heat exchangers, radiators etc. This paper investigates the heat transfer rate of Nano fluids using a shell and tube heat exchanger in single and multi tubes under turbulent flow condition by a forced convection mode. Alumina Nanoparticles are prepared by using Sol-Gel method. Heat transfer rate increases with decreasing particle size. In this experiment Alumina Nano particles of about 22 nm diameter used. Alumina Nano fluids are prepared with different concentrations of Alumina particles (0.13%, 0.27%, 0.4%, and 0.53%) with water as a base fluid using ultra-sonicator. Experiment have been conducted on shell and tube heat exchanger for the above concentrations on parallel and counter flow conditions by keeping constant inlet temperatures and mass flow rate. The result shows that the heat transfer rate is good compared to conventional fluids. The properties of Nano fluids and non-dimensional numbers have been calculated.

1 January 2024 in AIP Conference Proceedings
Verified
Conference Paper
Open access
PDF file
RBRoopsandeep Bammidi
Roopsandeep Bammidi
HMHymavathi Madivada
Hymavathi Madivada
SDSreeramulu Dowluru
Sreeramulu Dowluru
SPSrihari Palli
Srihari Palli
RSRakesh Chandmal CHANDMAL Sharma
Rakesh Chandmal CHANDMAL Sharma
VMVenkatesh Muddada
Venkatesh Muddada
The current work focused on the Mechano-Tribological Investigations of Metal-Ceramic Composites for which we considered Aluminium and Boron Nitride as metal and ceramic materials respectively. The study of properties like wear behaviour, hardness and friction coefficient was considered for different weight percentages of the alloy that was prepared using the technique of sand casting. The hardness of Metal-Ceramic composite is prepared based on standard procedures. These properties were studied under dry and wet conditions. The lubricants that were considered in this experiment are grease and SAE 40. The friction and wear mechanisms are studied under micro and Nanostructural observations. The experimental investigations helped us in observation and had a systematic study about the variations in the properties for weight percentages in the path of exploring the Mechano-Tribological properties.

17 June 2024 in Smart and Sustainable Manufacturing Systems
Verified
Journal Article
Closed access
SMSridhar Meka
Sridhar Meka
SDSreeramulu Dowluru
Sreeramulu Dowluru
LDLingaraju Dumpala
Lingaraju Dumpala
In modern industries, there is a growing demand for high-quality parts that are flexible, efficiently produced, and that minimize the wastage of raw materials to meet consumer needs. Computers are essential in various manufacturing sectors, but the integration of computer-aided design (CAD) and computer-aided manufacturing (CAM) remains a challenge for many industries. Feature recognition (FR) serves as a critical link in integrating CAD and CAM. This paper presents a concise review of CAD, CAM, and FR, as well as feature classifications, feature representation, feature recognition methods, and criticisms of different FR techniques in the context of prismatic, rotational, and sheet metal part features.