Sivasankara Raju Rallabandi

Dr. Sivasankara Raju Rallabandi

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2019 in Tribology International
Verified
Journal Article
Closed access
SRSivasankara Raju Rallabandi
Sivasankara Raju Rallabandi
MPM.K. Panigrahi
M.K. Panigrahi
RGR.I. Ganguly
R.I. Ganguly
GRG. Srinivasa Rao
G. Srinivasa Rao

1 July 2019 in Measurement
Verified
Journal Article
Closed access
SRSivasankara Raju Rallabandi
Sivasankara Raju Rallabandi
GRG. Srinivasa Rao
G. Srinivasa Rao
CSCHITRASEN SAMANTRA
CHITRASEN SAMANTRA

2 January 2024 in Engineering Research Express
Verified
Journal Article
Open access
PDF file
SRSivasankara Raju Rallabandi
Sivasankara Raju Rallabandi
LSLakshmi Srinivas
Lakshmi Srinivas
SPSrihari Palli
Srihari Palli
RSRAKESH CHANDMAL SHARMA
RAKESH CHANDMAL SHARMA
NSNeeraj Sharma
Neeraj Sharma
SSSunil Kumar Sharma
Sunil Kumar Sharma
Magnesium alloy of grade AZ91D is utilized for a variety of applications in aircraft design and frames, as well as vehicle engine radiators, bumpers, and suspension components to reduce the weight of automobiles. This research compared the mechanical, corrosion, wear, and erosion resistance of pure Mg to that of AZ91 alloy. The corrosion media was NaCl, NaOH, and MgSO4, and the weight loss method was utilised to evaluate corrosion. The pin-on-disc configuration was utilized to assess the dry sliding wear mechanism of the Pure Mg and AZ91D alloy. Pure monolithic Mg and AZ91D magnesium alloy have a low resistance to wear as a result of an increase in contact temperature brought about by a shift of operational conditions. Erosive wear is caused when solid particles in a liquid or air jet strike a surface. Significantly influencing the erosive wear are particle velocity, impact angle, and erodent particle size. In this work, the erosive wear of AZ91D was studied using an Air jet erosion tester. SiO2 was used as the eroding material, and the flow rate of the eroding material and air was 5 gm min−1. The erosive factor experiments are designed using Taguchi orthogonal array (L16). The erosive factor response is erosion rate and primarily regulated by three factors as angle (30°, 45°, 60°, and 90°), time (5 and 10 min) and, contact pressure (1 and 2 bar). The results of the experiments showed that the rate of wear increased with increasing pressure, and that the angle of impact of the jet at 60° caused the most wear of any of the tested angles. Analysis of variance (ANOVA) shows that time is the most important factor in determining erosive rate for AZ91D. SEM is used to investigate the structure and morphology of worn-out materials, and its findings are then confirmed.

15 May 2017 in Metallurgical and Materials Transactions A
Verified
Journal Article
Closed access
PDF file
SRSivasankara Raju Rallabandi
Sivasankara Raju Rallabandi
MPM. K. Panigrahi
M. K. Panigrahi
RGR. I. Ganguly
R. I. Ganguly
GRG. Srinivasa Rao
G. Srinivasa Rao

20 September 2017 in Tribology in Industry
Verified
Journal Article
Open access
SRSivasankara Raju Rallabandi
Sivasankara Raju Rallabandi
GRG.S. Rao
G.S. Rao

6 February 2024 in Journal of the Chinese Institute of Engineers
Verified
Journal Article
Closed access
SRSivasankara Raju Rallabandi
Sivasankara Raju Rallabandi
DPDevi Prasad Pilla
Devi Prasad Pilla
SDSreeramulu Dowluru
Sreeramulu Dowluru
SPSrihari Palli
Srihari Palli
NSNeeraj Sharma
Neeraj Sharma
RSRAKESH CHANDMAL SHARMA
RAKESH CHANDMAL SHARMA