In situ stress is an important parameter regulating the production of coalbed methane (CBM), and the monitoring of rock deformation can provide a description of the state of stress. Microseismic monitoring in a multistage fractured horizontal CBM well was conducted as a case study with a completion depth of 1445.36 m. The results show that there is a good correlation among the seismicity parameters, b-value, stress drop, fracture length, fracture density, and orientation. In the stress concentration region, the fracture is longer with a smaller density, where the b-value is lower. On the contrary, in the stress relaxation zone, the fracture is shorter with a complex shape, where the b-value is higher. Stress drop is relatively higher where fractures are concentrated, which indicate the areas with successful reservoir stimulation. The reliability of the above results was verified by the normal fault occurring between stages 7 and 8. In the area affected by the hanging wall of the normal fault (stage 6 and 7), the b-value is 0.38-0.39, while in the area affected by the footwall (stage 8 and 9), the b-value is 0.64-0.66. This phenomenon reflects an obvious stress concentration in the hanging wall of normal fault, which is consistent with the conventional understanding. The microseismic source parameters have great potential in evaluating reservoir stress. With further exploration of source parameters, microseismic will provide more support for CBM development.
The geological conditions of coal reservoirs in China are complex, and the reservoir permeability is generally lower. Multifracturing is an effective method of improving reservoir permeability and coalbed methane (CBM) production. In this study, two types of dynamic loads, CO2 blasting and a pulse fracturing gun (PF-GUN), were used to conduct multifracturing engineering tests in nine surface CBM wells in the Lu'an mining area in the central and eastern parts of the Qinshui Basin. The curves of pressure versus time of the two dynamic loads were obtained in the laboratory. The prepeak pressurization time of the PF-GUN was 200 ms, and that of the CO2 blasting was 2.05 ms, which just falls in the optimum pressurization time of multifracturing. The microseismic monitoring results revealed that, in terms of the fracture morphology, both the CO(2 )blasting and PF-GUN loads produced multiple sets of fractures in the near-well zone. In the six wells used for the CO2 blasting tests, an average of three branch fractures were produced outside of the main fracture, and the average angle between the main fracture and the branch fractures exceeded 60 & DEG;. In the three wells stimulated by PF-GUN, an average of two branch fractures were produced outside of the main fracture, and the average angle between the main fracture and the branch fractures was 25-35 & DEG;. The multifracture characteristics of the fractures formed via CO2 blasting were more obvious. However, a coal seam is a multifracture reservoir with a large filtration coefficient; the fracture will not extend after reaching the maximum scale under a certain gas displacement condition. Compared with the traditional hydraulic fracturing technique, the nine wells used in the multifracturing tests exhibited an obvious stimulation effect with an average increase of 51.4% in daily production. The results of this study provide an important technical reference for the efficient development of CBM in low- and ultralowpermeability reservoirs.
Nitrogen–slick water composite fracturing is a novel, recently developed fracturing technology. Due to its impact on increasing permeability, this technology outperforms hydraulic fracturing. This study adopted the horizontal well XJ-1L, Xinjing coal mine, Qinshui Basin, China, as a study area to statistically analyze the fracture properties, stress drop, and b-value distribution characteristics of 1217 effective micro-seismic events generated during nitrogen–water composite fracturing. The results show that: (1) gradually reducing the proportion of gas in fracturing fluid reduced the proportion of tensile fractures at a ratio of between 15.6% and 0.8%, whereas the proportion of strike-slip fractures gradually increased by between 1.6% and 15.2%; (2) the stress drop and b-values in the nitrogen fracturing (NF) stage, representative of stress disturbance, exceeded those in the hydraulic fracturing (HF) stage, consistent with greater numbers of tensile fractures formed in the NF stage; (3) the greater number of tensile fractures and their increasing permeability could be explained based on the influences of gas compressibility and pore pressure on coal fractures. This study provides a theoretical and practical basis for optimizing the exploitation of low-permeability coal reservoirs.
Disaster warning is crucial for coal mine safety. However, capturing the precursor information of disaster occurrence remains a challenging task, especially the spatiotemporal fractal characteristics of microseismic events before large-scale fractures in rock masses and their indicative significance for disasters. In this study, we proposed a method for precursor identification and early warning indication of high-energy microseismic events by a combination of temporal and spatial fractal of low-energy events based on a set of 78 days of on-site microseismic monitoring data. The rationality of this method was validated by numerical simulation, which focuses on the fractal characteristics of rock fracture morphology under compression loading. The results show: (1) Before the occurrence of high-energy microseismic events, the fractal dimension of the microseismic events in the time series was relatively low, and the variance and autocorrelation coefficient of the time fractal dimension showed an increasing trend, exhibiting a typical slowing down phenomenon. (2) The spatial fractal dimension of the microseismic events rapidly decreased to 1.3–1.5 before the occurrence of high-energy events, with an average decrease of over 0.48. (3) Microseismic events are associated products of coal rock mass fracture processes, and their uniqueness in time series and spatiotemporal evolution characteristics have important indicative significance for the incubation and early warning of coal rock mass disasters.