With the development of intelligent modern power systems, real-time sensing and monitoring of system operating conditions have become one of the enabling technologies. Due to their flexibility, robustness and broad serviceable scope, wireless sensor networks have become a promising candidate for achieving the condition monitoring in a power grid. In order to solve the problematic power supplies of the sensors, energy harvesting (EH) technology has attracted increasing research interest. The motivation of this paper is to investigate the profiles of harnessing the electric and magnetic fields and facilitate the further application of energy scavenging techniques in the context of power systems. In this paper, the fundamentals, current status, challenges, and future prospects of the two most applicable EH methods in the grid—magnetic field energy harvesting (MEH) and electric field energy harvesting (EEH) are reviewed. The characteristics of the magnetic field and electric field under typical scenarios in power systems is analyzed first. Then the MEH and EEH are classified and reviewed respectively according to the structural difference of energy harvesters, which have been further evaluated based on the comparison of advantages and disadvantages for the future development trend.
Measurement errors of a capacitive voltage transformer (CVT) are relevant to its equivalent parameters for which its capacitive divider contributes the most. In daily operation, dielectric aging, moisture, dielectric breakdown, etc., it will exert mixing effects on a capacitive divider’s insulation characteristics, leading to fluctuation in equivalent parameters which result in the measurement error. This paper proposes an equivalent circuit model to represent a CVT which incorporates insulation characteristics of a capacitive divider. After software simulation and laboratory experiments, the relationship between measurement errors and insulation parameters is obtained. It indicates that variation of insulation parameters in a CVT will cause a reasonable measurement error. From field tests and calculation, equivalent capacitance mainly affects magnitude error, while dielectric loss mainly affects phase error. As capacitance changes 0.2%, magnitude error can reach −0.2%. As dielectric loss factor changes 0.2%, phase error can reach 5′. An increase of equivalent capacitance and dielectric loss factor in the high-voltage capacitor will cause a positive real power measurement error. An increase of equivalent capacitance and dielectric loss factor in the low-voltage capacitor will cause a negative real power measurement error.
To facilitate better interpretation of dielectric response measurements—thereby directing numerical evidence for condition assessments of oil-paper-insulated equipment in high-voltage alternating current (HVAC) transmission systems—a novel approach is presented to estimate the parameters in the extended Debye model (EDM) using wideband frequency domain spectroscopy (FDS). A syncretic algorithm that integrates a genetic algorithm (GA) and the Levenberg-Marquardt (L-M) algorithm is introduced in the present study to parameterize EDM using the FDS measurements of a real-life 126 kV oil-impregnated paper (OIP) bushing under different controlled temperatures. As for the uncertainty of the EDM structure due to variable branch quantity, Akaike’s information criterion (AIC) is employed to determine the model orders. For verification, comparative analysis of FDS reconstruction and results of FDS transformation to polarization–depolarization current (PDC)/return voltage measurement (RVM) are presented. The comparison demonstrates good agreement between the measured and reconstructed spectroscopies of complex capacitance and tan δ over the full tested frequency band (10−4 Hz–103 Hz) with goodness of fit over 0.99. Deviations between the tested and modelled PDC/RVM from FDS are then discussed. Compared with the previous studies to parameterize the model using time domain dielectric responses, the proposed method solves the problematic matching between EDM and FDS especially in a wide frequency band, and therefore assures a basis for quantitative insulation condition assessment of OIP-insulated apparatus in energy systems.
25 August 2017 in IEEE Transactions on Industrial Electronics
To address the lack of reliable power supplies for lightning current measurement systems (LCMS), this paper proposes a novel self-powered LCMS. The required operation power of a LCMS can be provided by harvesting the surge current that is measured using a power coil such that the system can be energized to complete a single-cycle measurement and data recording. In this manner, the stand-alone LCMS is triggered by lightning currents, and, hence, the signal acquisition can be activated automatically. In particular, this paper designs a two-channel passive peak-holding circuit as a low-power substitution to the conventional high-speed sampling modules. The polarity, current peak, and trigger time can be measured and ultimately be stored in a nonvolatile memory. The theoretical and simulation studies are presented in detail to determine the structure, size, and number of winding turns of the power and signal coils. The circuitry design of the power supply and signal conditioning units are also addressed. Experimental results verify that the proposed LCMS can accurately measure the amplitudes of lightning currents, achieving an accuracy of a maximum error of 4%, while the LCMS is fully self-powered to satisfy the energy demand from the measurement and data acquisition tasks.
20 April 2022 in IEEE Transactions on Dielectrics and Electrical Insulation
Despite the technical popularity of the dielectric response (DR) methods used for the nonintrusive diagnosis of the cellulose insulation condition, it is still considered a challenging and tough task so far to trustworthily interpret the details of the measurement results for further understanding and tracing the insulation changes behind. From a novel perspective of parametric study on the circuital DR equivalence of cellulosic insulation—extended Debye model (EDM), the new dielectric characteristic quantities and the quantification approach to determine the cellulosic moisture condition are investigated in the present study. First, a kind of tailor-made scale-down bushing model is prepared, with its cellulosic condenser body absorbing differently controlled quantities of water to simulate the dampness of real-life insulation, of which the frequency-domain spectroscopy (FDS) is measured under controlled temperatures. Then, the EDM is employed for a parameterized study on the FDS details with the moisture changes, by identifying the model parameters against the FDS curves, whereby the two time-domain dielectric spectra—polarization/depolarization current and return voltage—are transferred from the FDS so that a set of hybrid time–frequency characteristic quantities is proposed, which is revealed to be indicative of the dampness variations of cellulosic insulation. Finally, the principal component analysis and the feature recognition algorithm based on minimum distance are applied to determine the moisture content of the condenser body, which verifies the holistic effectiveness of the proposed method.
Enhancing the energy storage properties of dielectric polymer capacitor films through composite materials has gained widespread recognition. Among the various strategies for improving dielectric materials, nanoscale coatings that create structurally controlled multiphase polymeric films have shown great promise. This approach has garnered considerable attention in recent years due to its effectiveness. This review examines surface-coated polymer composites used for dielectric energy storage, discussing their dielectric properties, behaviors, and the underlying physical mechanisms involved in energy storage. The review thoroughly examines the fabrication methods for nanoscale coatings and the selection of coating materials. It also explores the latest advancements in the rational design and control of interfaces in organic–inorganic, organic–organic, and heterogeneous multiphase structures. Additionally, the review delves into the structure–property relationships between different interfacial phases and various interface structures, analyzing how nanoscale coatings the impact dielectric constant, breakdown strength, conduction and charge transport mechanisms, energy density and efficiency, thermal stability, and electrothermal durability of polymeric capacitor films. Moreover, the review summarizes relevant simulation methods and offers computational insights. The potential practical applications and characteristics of such nanoscale coating techniques are discussed, along with the existing challenges and practical limitations. Finally, the review concludes with a summary and outlook, highlighting potential research directions in this rapidly evolving field.