Lithium-ion batteries (LIBs) have the lead as the most used power source for electric vehicles and grid storage systems, and a battery thermal management system (BTMS) can ensure the efficient and safe operation of lithium-ion batteries. Epoxy resin board (ERB) offers a wide range of applications in LIBs due to its significant advantages such as high dielectric strength, electrical insulation, good mechanical strength, and stiffness. This study proposes an air-cooled battery module comprised of sixteen prismatic batteries incorporating an ERB layer between the batteries. To compare the performance of the ERB-based air-cooling system, two other air-cooling structures are also assessed in this study. Three-dimensional numerical models for the three cases are established in this paper, and the heat dissipation processes of the battery module under varying discharge rates (1C, 2C, and 5C) are simulated and analyzed to comprehensively evaluate the performance of the different cooling systems. Comparative simulations reveal that incorporating ERB into the battery assembly significantly reduces battery surface temperatures and promotes temperature uniformity across individual batteries and the entire pack at various discharge rates. Notably, under 5C discharge conditions, the ERB-based thermal management system achieves a maximum battery surface temperature increase of 16 °C and a maximum temperature difference of 8 °C between batteries. Additionally, this paper also analyzes the impact of battery arrangement on air-cooling system performance. Therefore, further optimization of the structural design or the integration of supplementary cooling media might be necessary for such demanding conditions.

Lithium-ion batteries (LIBs) are widely used as power sources for electric vehicles due to their various advantages, including high energy density and low self-discharge rate. However, the safety challenges associated with LIB thermal runaway (TR) still need to be addressed. In the present study, the effects of the battery SOC value and coolant flow rate on the TR behavior in a LIB pack are comprehensively investigated. The battery pack consists of 10 18650-type LIBs applied with the serpentine channel liquid-cooling thermal management system (TMS). The TR tests for various SOC values (50%, 75% and 100%) and coolant flow rates (0 L/h, 32 L/h, 64 L/h and 96 L/h) are analyzed. The retarding effect of the TMS on TR propagation is found to be correlated with both the coolant flow rate and the battery SOC value, and a larger coolant flow rate and lower SOC generally result in fewer TR batteries. Furthermore, the TR propagation rate, evaluated by the time interval of TR occurrence between the adjacent batteries, increases with the battery SOC. The battery pack with 100% SOC shows more rapid TR propagation, which can be completed in just a few seconds, in contrast to several minutes for 50% and 75% SOC cases. In addition, the impact of the battery SOC and coolant flow rate on the maximum temperature of the TR battery is also examined, and no determined association is observed between them. However, it is found that the upstream batteries (closer to the external heater) show a slightly higher maximum temperature than the downstream ones, indicating a weak association between the TR battery maximum temperature and the external heating duration or the battery temperature at which the TR starts to take place.

In recent years, immersion cooling has gained wide interest for thermal management of lithium-ion batteries. Usually, dielectric oils or fluorinated liquid are used as immersion coolants to avert short circuits, but they have low thermal conductivity and high cost. Although water offers superior heat-transfer performance, its poor dielectric property means it cannot be used directly as an immersion coolant. Near full-depth partial immersion (NFDPI) was proposed as a viable alternative, in which water does not contact the tabs of batteries. In this study, an NFDPI experimental system is set up, and the effects of coolant flow rate, discharge rate, and inlet–outlet configuration on thermal management performance are investigated. Since direct observation of the immersion tank’s internal flow is challenging, numerical simulations are conducted to resolve the flow field under various operating conditions. The experimental and simulated results reveal that NFDPI cooling effectively limits the module’s maximum temperature, and the module’s maximum temperature spread is mainly attributed to the cell’s vertical temperature gradient. These findings offer guidance for the practical deployment of water-based NFDPI lithium-ion battery energy storage systems.

Unlike incandescent light bulb, which radiates heat into the surroundings by infrared rays, light emitting diode (LED) traps heat inside the lamp. This fact increases the difficulty of cooling LED lamps, while it facilitates the recovery of the generated heat. We propose a novel energy system that merges high-power LED lamp cooling with the heat pump use; the heat pump can cool the LED lamp and at the same time recover the waste heat. In this way, a high percentage of the energy consumed by the LED lamp can be utilized. In this work, we developed a prototype of this energy system and conducted a series of experimental studies to determine the effect of several parameters, such as cooling water flow rate and LED power, on the LED leadframe temperature, compressor power consumption, and system performance. The experimental results clearly indicate that the energy system can lead to substantial energy savings.