Background/Objectives: Antibiotic contamination in water sources is a growing global concern, contributing to environmental degradation and the proliferation of antimicrobial resistance. Traditional treatment methods, such as advanced oxidation or high-pressure membrane processes, are often energy-intensive and economically unsustainable for large-scale or decentralized applications. This study explores the potential of two cost-effective, commercially available metal–organic frameworks (MOFs), ZIF-8 and F300, to improve the performance of membrane-based filtration–adsorption systems for removing tetracycline and sulfadiazine from water. Methods: Batch adsorption experiments were performed to evaluate the uptake capacities, kinetics, and isotherms of both MOFs toward the selected antibiotics. The membranes were modified using a low-cost silane-assisted deposition of MOF particles and tested in a microfiltration system. Removal efficiencies and water permeability were assessed and kinetic and isotherm models were applied to understand the adsorption mechanisms. Results: ZIF-8 showed superior adsorption performance, with maximum capacities of 442.2 mg/g for tetracycline and 219.3 mg/g for sulfadiazine. F300 was effective only for tetracycline. Membranes modified with ZIF-8 improved pharmaceutical removal by 187% (tetracycline) and 224% (sulfadiazine) compared to unmodified membranes. Although permeability decreased due to increased hydrophobicity, the materials and processes remained economically favorable. Conclusions: This study demonstrates that MOF-modified ceramic membranes, particularly those incorporating ZIF-8, offer a low-cost, scalable, and energy-efficient alternative for pharmaceutical removal from water. The approach combines strong environmental impact with economic viability, making it attractive for broader implementation in water treatment systems.
The study aims to eliminate the effect of coalescing filter blocking due to on–off operation by changing the wetting properties of the non-woven fiberglass filter media through their chemical modification with the use of a polydimethylsiloxane (PDMS) solution in hexane and a few commercial products that give the surface oleophobic properties. The best results—high separation efficiency, no redispersion of droplets at the outlet, and low flow resistance—were obtained for materials coated by immersion in a 0.2% PDMS solution, for which a reduction in oleophilicity was found, but the material was not oleophobic and still moderately wetted with the test liquid. The corresponding static contact angle with the VG-46 rotary compressor oil measured on the flat borosilicate glass wafer made of the same material as the fiberglass media was equal to 54° for the PDMS dip-coated surface. Moreover, the good stability of the applied polymer on the material surface was confirmed by the SEM imaging, the FTIR analysis, and maintaining a high performance in multiple tests run for a single coalescing element.
Nanoparticles (interchangeably called ultrafine particles) constitute one of the growing risks encountered in everyday life. Both short- and long-term exposure to them, as well as to particulate matter in general, may pose serious health risks. In this study, we focus on monitoring of particle concentration in urban air for 200 days, with special attention to nanoparticles. The overall data coverage exceeded 80%, reaching over 97% in three selected months. Measurements were carried out at 25.5 m height in southern Warsaw, in close vicinity to residential blocks with apartments also at the same level. Data were collected from January to first half of August 2025 using a Grimm MINI-WRAS portable wide-range aerosol spectrometer and a thermo-hygro-barometer. Over the 8-month period, significant variations between months and days in both nanoparticle and all particulate matter concentrations were observed. Winter months were almost four times more polluted with particles (both nanoparticles and those above 100 nm) than spring and summer periods. Although nanoparticle concentration in colder months was higher, the percentage of nanoparticles was lower. An important aspect of these investigations was comparing the obtained results with publicly available air pollution data from urban air quality monitoring stations, which represent ground-level measurements. At rooftop altitude, PM2.5/PM10 ratios were significantly higher than those measured at ground level.