The main problem of recycling aluminium scrap is the gradual accumulation of impurities, especially iron, which tend to form undesired intermetallic compounds that affect the integrity and the mechanical performance of the castings. In this paper, we aim to provide an overview on the topic of iron removal from aluminium melts through primary intermetallic precipitation and the progress made during the LiME Hub project to understand the process and to develop a more efficient procedure. We cover both thermodynamic analysis and experimental validation. We found that high shear melt conditioning technology enhances the typically slow nucleation and growth of the dense primary intermetallics, speeding up their sedimentation and allowing a faster removal of Fe from the melt by simple gravity sedimentation. It also promotes the formation of smaller and more compact Fe-rich intermetallics, allowing an increased volume fraction recovery and mitigating their effect of being present in the final castings. The technology is not limited to batch processing, with a 90% efficiency, but can also be applied to continuous melt treatment of aluminium scrap, with currently 60% efficiency, and could be combined with other solid–liquid separation techniques to increase the purification efficiency even more.
The search for more efficient methods for degassing aluminum alloy melts has always been of great interest for the metal industry because the presence of hydrogen and oxides in the melts’ prior casting was detrimental to the integrity and properties of the final products. In this work, we present an overview of the progress and key findings from the research and development of an innovative High Shear Melt Conditioning (HSMC) degassing technology during the Liquid Metal Engineering (LiME) Research Hub project. Compared to conventional rotary degassing, this novel technique was capable of working at higher rotor speeds to efficiently break and disperse the naturally occurring oxide bifilms in the melt and to capture and disperse each supplied inert gas bubble into many tiny bubbles throughout the whole melt. This resulted in the elimination of the need to degas fluxes to remove the oxides in the melt, the reduction in the gas flow required to reach the same level of hydrogen removal rate, and the minimization of the regassing effect after processing. The increased process efficiency allowed for reduced melt processing costs and, at the same time, improved the melt quality, which resulted in fewer defects and improved mechanical properties.
High-shear melt conditioning (HSMC) technology was used for degassing and de-ironing of an aluminum alloy recovered from the Zorba cast fraction of the non-ferrous scrap from shredded end-of-life vehicles. The results showed that the recovery of aluminum alloys from the Zorba cast fraction was more than 80%. High-shear melt conditioning improved the degassing process during melt treatment in comparison with the adding of degassing tablets. The efficiency of the de-ironing process using HSMC increased by up to 24% after, increasing the Mn content to 0.8% in the melt. Adding Mn to Zorba melt enhanced the de-ironing process and eliminated the formation of β-AlFeSi intermetallic particles, which have a detrimental effect on both the mechanical and corrosion properties of the alloy.
The melt conditioned direct chill (MC-DC) casting process has been used for the production of billets of AA-6111 alloy formulated from recycled aluminium derived from incinerator bottom ash (IBA). The billets were homogenised and then extruded into planks. Optical metallography of the MC-DC billets showed equiaxed refined grains in comparison to DC and grain refined (DC-GR) billets formulated from the same scrap source. Microstructure evaluation for the extruded planks showed a less extensive peripheral coarse grain (PCG) for the MC-DC sample.
The melt conditioned direct chill (MC-DC) casting process has been used to produce billets and extruded planks of AA5754 alloy formulated from 100% recycled Taint Tabor scrap aluminum. The billets were homogenized and then extruded into flat planks. Optical metallography of the MC-DC cast billets showed equiaxed refined grains in comparison to conventional direct chill (DC) cast and direct chill grain refined (DC-GR) cast billets formulated from the same Taint Tabor scrap. Microstructural evaluation of the extruded planks showed extensive peripheral coarse grain (PCG) for the DC, DC-GR and MC-DC cast planks. The 2 mm and 1 mm MC-DC cast planks produced after cold rolling and heat treatment showed a fully recrystallized microstructure at 380 °C and 300 °C for 10 min respectively with an improvement in mechanical properties over DC-GR cast and similarly processed planks. The as-extruded MC-DC cast planks tensile tested in the transverse direction showed 34% elongation and 213 MPa ultimate tensile strength. These tensile results showed 5.8% higher elongation and 1.2% higher ultimate tensile strength compared with the DC-GR planks after applying high shear melt conditioning.