The search for more efficient methods for degassing aluminum alloy melts has always been of great interest for the metal industry because the presence of hydrogen and oxides in the melts’ prior casting was detrimental to the integrity and properties of the final products. In this work, we present an overview of the progress and key findings from the research and development of an innovative High Shear Melt Conditioning (HSMC) degassing technology during the Liquid Metal Engineering (LiME) Research Hub project. Compared to conventional rotary degassing, this novel technique was capable of working at higher rotor speeds to efficiently break and disperse the naturally occurring oxide bifilms in the melt and to capture and disperse each supplied inert gas bubble into many tiny bubbles throughout the whole melt. This resulted in the elimination of the need to degas fluxes to remove the oxides in the melt, the reduction in the gas flow required to reach the same level of hydrogen removal rate, and the minimization of the regassing effect after processing. The increased process efficiency allowed for reduced melt processing costs and, at the same time, improved the melt quality, which resulted in fewer defects and improved mechanical properties.
The main problem of recycling aluminium scrap is the gradual accumulation of impurities, especially iron, which tend to form undesired intermetallic compounds that affect the integrity and the mechanical performance of the castings. In this paper, we aim to provide an overview on the topic of iron removal from aluminium melts through primary intermetallic precipitation and the progress made during the LiME Hub project to understand the process and to develop a more efficient procedure. We cover both thermodynamic analysis and experimental validation. We found that high shear melt conditioning technology enhances the typically slow nucleation and growth of the dense primary intermetallics, speeding up their sedimentation and allowing a faster removal of Fe from the melt by simple gravity sedimentation. It also promotes the formation of smaller and more compact Fe-rich intermetallics, allowing an increased volume fraction recovery and mitigating their effect of being present in the final castings. The technology is not limited to batch processing, with a 90% efficiency, but can also be applied to continuous melt treatment of aluminium scrap, with currently 60% efficiency, and could be combined with other solid–liquid separation techniques to increase the purification efficiency even more.
High-shear melt conditioning (HSMC) technology was used for degassing and de-ironing of an aluminum alloy recovered from the Zorba cast fraction of the non-ferrous scrap from shredded end-of-life vehicles. The results showed that the recovery of aluminum alloys from the Zorba cast fraction was more than 80%. High-shear melt conditioning improved the degassing process during melt treatment in comparison with the adding of degassing tablets. The efficiency of the de-ironing process using HSMC increased by up to 24% after, increasing the Mn content to 0.8% in the melt. Adding Mn to Zorba melt enhanced the de-ironing process and eliminated the formation of β-AlFeSi intermetallic particles, which have a detrimental effect on both the mechanical and corrosion properties of the alloy.
A continuous high-shear melt conditioning twin-roll casting process has been developed for production of recycled aluminum alloy strip with minimum casting defects. High-shear melt conditioning is applied to increase the impurities tolerance of recycled aluminum. The results of this study showed that solidification during twin-roll casting can be controlled by using intensive melt conditioning prior to casting, which can promote equiaxed growth with minimal defects and result in improved sheet quality. Melt-conditioned twin-roll cast (MC-TRC) AA5754 alloy exhibited fine equiaxed grains and homogenized matrix structure while centerline segregation was eliminated. As-cast melt-conditioned twin-roll cast AA5754 strips showed clear grain recrystallization after thermomechanical treatment at 430°C for 30 min, representing an improvement over conventional twin-roll casting. The MC-TRC strip showed 57.2% higher elongation and 4.1% higher ultimate tensile strength compared with the TRC strip after applying melt conditioning with thermomechanical treatment.
The impact of high shear melt conditioning on the morphology and distribution of Fe intermetallic compounds was investigated in the processing of recycled AA6111 alloy by the twin roll casting process. The optical and scanning electron microscope (SEM) micrograph studies were carried out on twin roll casting (TRC) and melt conditioning twin roll casting (MC-TRC) samples. The microstructural analysis showed fine and uniformly distributed Fe-rich intermetallic phases for MC-TRC strips compared with the TRC strips. There was a significant improvement in the mechanical properties of MC-TRC strips after applying melt conditioning. The as-cast MC-TRC samples showed 18.7%, 19.2% and 9.8% increases in elongation, yield strength and ultimate tensile strength, respectively, in the longitudinal direction, while in the transverse section, the MC-TRC samples showed 32.3%, 2.2% and 3.8% increases in elongation, yield strength and ultimate tensile strength, respectively.
The melt conditioned direct chill (MC-DC) casting process has been used for the production of billets of AA-6111 alloy formulated from recycled aluminium derived from incinerator bottom ash (IBA). The billets were homogenised and then extruded into planks. Optical metallography of the MC-DC billets showed equiaxed refined grains in comparison to DC and grain refined (DC-GR) billets formulated from the same scrap source. Microstructure evaluation for the extruded planks showed a less extensive peripheral coarse grain (PCG) for the MC-DC sample.