This research evaluates the rheological and mechanical properties of polymer- and nanomaterials-modified bitumen by incorporating nanosilica (NSA), nanoclay (NCY), and Acrylonitrile Styrene Acrylate (ASA) at 5% by weight of the bitumen. The samples were prepared at 165 °C for one hour to obtain homogeneous blends. All samples were subjected to short- and long-term aging to simulate the effects of different operating conditions. The research conducted a series of tests, including consistency, frequency sweep, and multiple creep stress and recovery (MSCR) using the dynamic shear rheometer (DSR) and bending beam rheometer (BBR). The results showed that all modified bitumen outperformed the neat bitumen. The frequency sweep showed a higher complex modulus (G*) and lower phase angle (δ), indicating enhanced viscoelastic properties and, thus, higher resistance to permanent deformation. The BBR test revealed that the bitumen modified with NCY5% has a creep stiffness of 47.13 MPa, a 51.5% improvement compared to the neat bitumen, while the NSA5% has the highest m-value, a 28.5% enhancement compared with the neat bitumen. The MSCR showed that the modified blends have better recovery properties and, therefore, better resistance to permanent deformation under repeated loadings. The aging index demonstrated that the modified bitumen is less vulnerable to aging and maintains their good flexibility and resistance to permanent deformations. Finally, these results showed that adding 5% polymer and nanomaterials improved the bitumen’s’ performance before and after aging by reducing permanent deformation and enhancing crack resistance at low temperatures, thus extending the pavement service life and making them an effective alternative for improving pavement performance in various climatic conditions and under high traffic loads.
11 September 2022 in Journal of Advanced Research in Applied Sciences and Engineering Technology
Previous parallel computing implementations for Computational Fluid Dynamics (CFD) focused extensively on Complex Instruction Set Computer (CISC). Parallel programming was incorporated into the previous generation of the Raspberry Pi Reduced Instruction Set Computer (RISC). However, it yielded poor computing performance due to the processing power limits of the time. This research focuses on utilising two Raspberry Pi 3 B+ with increased processing capability compared to its previous generation to tackle fluid flow problems using numerical analysis and CFD. Parallel computing elements such as Secure Shell (SSH) and the Message Passing Interface (MPI) protocol were implemented for Advanced RISC Machine (ARM) processors. The parallel network was then validated by a processor call attempt and core execution test. Parallelisation of the processors enables the study of fluid flow and computational fluid dynamics (CFD) problems, such as validation of the NACA 0012 airfoil and an additional case of the Laplace equation for computing the temperature distribution via the parallel system. The experimental NACA 0012 data was validated using the parallel system, which can simulate the airfoil's physics. Each core was enabled and tested to determine the system's performance in parallelising the execution of various programming algorithms such as pi calculation. A comparison of the execution time for the NACA 0012 validation case yielded a parallelisation efficiency above 50%. The case studies confirmed the Raspberry Pi 3 B+'s successful parallelisation independent of external software and machines, making it a self-sustaining compact demonstration cluster of parallel computers for CFD.
22 November 2022 in Advances in Materials Science and Engineering
The effect of aluminum oxide nanoparticles (Al2O3) on the 60/70 penetration of asphalt cement (AC) was investigated in terms of the physical and rheological characteristics by using the Superpave testing procedures. Al2O3 at 3, 5, and 7% concentrations were blended with 60/70 penetration of grade AC. Conventional testing procedures were adopted regarding the physical characteristics, while dynamic shear rheometer (DSR) testing procedures were conducted to evaluate the high and low temperature failure parameters. In addition, heuristic modelling techniques, artificial neural networks (ANN), and support vector machines (SVM) were employed to predict the performance characteristics of AC by using the mechanical testing conditions. The frequency sweep test and multiple stress creep recovery (MSCR) test results revealed that the optimum composition of Al2O3 was at 5% concentration considering the high temperature performance characteristics since further addition of the Al2O3 resulted in degradation in the enhanced properties due to agglomeration of the nanoparticles in the blend. On the contrary, Al2O3 5% demonstrated the lowest viscoelastic behavior at intermediate temperatures. The higher complex modulus () and lower phase angle () parameters indicated that the increase in stiffness due to the modification process was at the cost of losing elastic properties against fatigue cracking. Moreover, based on the statistical performance indicator, coefficient of determination (R2), it was observed that the ANN models for predicting and achieved a prediction accuracy of 0.989 and 0.911 while SVM models were able to achieve 0.984 and 0.929, respectively, considering the training datasets. On the other hand, it was noted that SVM models outperformed the ANN models in terms of a smaller gap between the results obtained from the training and testing datasets. The difference between the training and testing datasets for and parameters for the SVM models were 3.2% and 6.8% while for the ANN models, the differences were 11.6% and 9.5%, respectively, indicating that the ANN models were more prone to the overfitting phenomenon.
The influence of Acrylate Styrene Acrylonitrile (ASA) and ASA/nanosilica (ASA/Si) additives was investigated by using a dynamic shear rheometer (DSR). Firstly, an ASA polymer was blended with the virgin asphalt binder at two different concentrations (3% ASA and 5% ASA). After observing that 5% ASA was the optimum concentration for modification, nanosilica particles were further incorporated into the 5% ASA-modified asphalt binder with two different percentages (5% ASA 3%Si; 5% ASA 5%Si). Frequency sweep tests were conducted across various frequencies at elevated temperatures. The experimental outcomes were analyzed using master curves, rutting, and fatigue resistance parameter plots. Additionally, to provide a more holistic analysis, two different multicriteria decision analysis (MCDA) techniques, namely the Preference Ranking Organization Method for Enrichment Evaluations (PROMETHEE) and the Technique for the Order of Preference by a Similarity to Ideal Solution (TOPSIS), were conducted to identify the best-performing asphalt binder by considering three different parameters: workability, performance under different conditions, and cost. The frequency sweep tests showed that the 5% ASA 5%Si asphalt worked best in terms of resistance to rutting. On the other hand, the virgin binder performed better than all modified binders when it failed to resist fatigue. On the other hand, the PROMETHEE analysis identified the 5% ASA-modified asphalt binder as the optimal choice, while the TOPSIS analysis determined that the 5% ASA 3%Si-modified binder provided the best performance. The differences between the experimental results and the MCDA were due to using more than one evaluation parameter and looking at how well the asphalt binder worked at different temperature ranges at the same time.
Tr en The current study focuses on the effect of Acrylate-styrene-acrylonitrile (ASA)/Nanosilica (Si) modified binders on the complex modulus (G*) and rutting resistance parameters (G*/ sinδ) of Asphalt Cement (AC). Four different blends including the base binder and the polymer nanocomposites which were formed by blending 5% ASA to base binder with the addition of nanosilica at 3, 5 and 7% by the weight were the subject of investigations. Conventional and Dynamic Shear Rheometer (DSR) testing procedures were conducted as well as morphology analysis using Fourier Transform Infrared Spectroscopy (FT-IR). The rheological characteristics of AC were analysed by master curves, isochronal plots and rutting resistance parameter plots. Test results revealed that G* and G*/ sinδ of all modified samples were significantly enhanced compared to the base binder. Multiple Stress Creep Recovery Test (MSCRT) conducted at 100 Pa and 3200 Pa showed that, non-recoverable compliance was reduced and elastic recovery of modified binders were improved. Optimum concentration was found to be 5% ASA/Si composite, as further addition of polymer nanocomposite resulted in lower enhancement in the rheological properties of modified AC due to the occurrence of agglomeration between the composite and the base binder. The current study focuses on the effect of Acrylate-styrene-acrylonitrile (ASA)/Nanosilica (Si) modified binders on the complex modulus (G*) and rutting resistance parameters (G*/ sinδ) of Asphalt Cement (AC). Four different blends including the base binder and the polymer nanocomposites which were formed by blending 5% ASA to base binder with the addition of nanosilica at 3, 5 and 7% by the weight were the subject of investigations. Conventional and Dynamic Shear Rheometer (DSR) testing procedures were conducted as well as morphology analysis using Fourier Transform Infrared Spectroscopy (FT-IR). The rheological characteristics of AC were analysed by master curves, isochronal plots and rutting resistance parameter plots. Test results revealed that G* and G*/ sinδ of all modified samples were significantly enhanced compared to the base binder. Multiple Stress Creep Recovery Test (MSCRT) conducted at 100 Pa and 3200 Pa showed that, non-recoverable compliance was reduced and elastic recovery of modified binders were improved. Optimum concentration was found to be 5% ASA/Si composite, as further addition of polymer nanocomposite resulted in lower enhancement in the rheological properties of modified AC due to the occurrence of agglomeration between the composite and the base binder.