Jakub Harvanec

Mr. Jakub Harvanec

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 December 2024 in Coatings
Verified
Journal Article
Open access
PDF file
Frantisek NovyFrantisek Novy
Frantisek Novy
JHJakub Harvanec
Jakub Harvanec
MMMiloš Mičian
Miloš Mičian
Heat treatment technology changes all the mechanical properties of metallic materials. The influence of induction hardening, nitriding and boronising on the change in the microhardness, impact toughness, microstructure and coefficient of friction of conventional steels 42CrMo4 and 32CrMo12 has been examined and compared with results obtained in the sintered steels with an increased content of Cu, which were prepared using powder metallurgy technology. Widely used treatments for the examined materials include induction hardening and gas nitriding. This study focuses on comparing those technologies with alternative technologies of boronising. It was found that for powder metallurgy materials, boronising is a much more suitable process than nitriding because after the application of nitriding, the impact toughness dropped to one third of the impact toughness of the base material, while after boronising, the impact toughness remained unchanged. Through boronising, it was possible to achieve the unique possibility of improving the mechanical properties of sintered PM Fe-Cu-C steels and fully replacing the currently used nitriding process. Furthermore, compared to nitriding, it also increases the hardness of the surface layer many times to improve the friction properties and significantly increases the impact toughness.

1 January 2025 in Technológ
Verified
Journal Article
Closed access
PDF file
UŽUniversity of Žilina
University of Žilina
JHJakub Harvanec
Jakub Harvanec
MMMiloš Mičian
Miloš Mičian
Martin FrátrikMartin Frátrik
Martin Frátrik
High-strength steels (HSS) are crucial in the production of lightweight structures. Their welding creates a distinct heterogeneous heat-affected zone (HAZ) in which a softened zone with locally lower mechanical properties forms. This critical zone acts as a weak point, concentrates strain, and can initiate failure, thereby compromising the structural integrity of the welded joint. Detailed understanding of the local behaviour of this zone is insufficiently investigated. Standard tests provide only basic data, which limits the reliability of simulations and the integrity assessment of steel structures. The article deals with the characterization of the local mechanical properties and deformation behaviour of the HAZ softened zone using the DIC (Digital Image Correlation) and nanoindentation techniques. The combined approach enables a comprehensive understanding of the mechanical properties of the HAZ subzones, crucial for assessing the reliability and integrity of welded structures.

1 January 2024 in Technológ
Verified
Journal Article
Open access
PDF file
UŽUniversity of Žilina
University of Žilina
JHJakub Harvanec
Jakub Harvanec
MMMiloš Mičian
Miloš Mičian
Frantisek NovyFrantisek Novy
Frantisek Novy
The heat treatment technology changes all sorts of materials properties. We examined the change of tribological properties of selected powder metallurgy materials and conventional steels, in this article. We used special testing equipment, for measuring the changes of friction coefficient of individual tested materials, before application of the heat treatment and after application of the heat treatment. We tested two types of powder metallurgy steels and two types of conventional steels. The changes in friction coefficient are shown in the table and charts. We used boronising, nitriding and surface hardening as procedures of heat treatment.

3 June 2026 in Powders
Verified
Journal Article
Open access
PDF file
EKElena Kantoríková
Elena Kantoríková
JHJakub Harvanec
Jakub Harvanec
Monika MadejMonika Madej
Monika Madej
JKJoanna Kowalczyk
Joanna Kowalczyk
With the increasing demands on energy efficiency and dynamic stability of modern combustion engines (e.g., TDI systems), conventional powder metallurgy materials are reaching their limits in terms of fatigue life and surface integrity. This scientific problem has led to the need to develop hybrid metal matrix (MMC) systems that use in situ hard phase formation. This study presents a comparative analysis of two real industrial components representing hybrid systems with a uniquely high content of titanium and vanadium (>1% by weight). The Ni-Mo-Ti system and the high-carbon C-Cu-Ti system were compared. The samples were processed by steam oxidation and plasma nitriding at 200 °C after sintering. The experimental methodology included chemical analysis on the Bruker Q2 ION 2 instrument, 10-point EDX analysis (Phenom), measurement of the apparent hardness of HV10 and dynamic ball-on-disc tribological tests at a load of 5.00 N supplemented by 3D profilometry. The results showed that the Ni-Mo-Ti system achieves higher hardness at functional edges (256 HV10) and three times higher resistance to deep penetration (11.46 μm vs. 34.67 μm) compared to the C-Cu-Ti system. Topographic analysis confirmed the positive role of porosity as a micro-reservoir for abrasion particles (negative Ssk). The study confirms that the nickel–molybdenum matrix ensures more efficient fixation of in situ generated TiC carbides, thus providing higher functional stability for automotive applications, which was verified by the non-destructive vibroacoustic diagnostics of Polytec PSV-500.