The article deals with the analysis of one of the methods of selecting rational parameters of automated clutch control system for robotic transmission. The objective is to select rational parameters of automated clutch control system for robotic transmission, equipped with electropneumatic actuating mechanism on the basis of mathematical simulation. The depicted mathematical simulation of the clutch control system is characterized by the possibility to coordinate the algorithm of control unit with the dynamic processes in the execution device. The new functional interrelations between the elements of the electro-pneumatic actuator are mathematically described. The way to the selection of rational parameters of an automated control system for clutch is recommended; the selection taking into account the features of the electro-pneumatic actuator. Using the mathematical modeling method, rational control parameters of the automated clutch control system are determined. Based on comparative experimental researches, an inaccuracy is calculated for the mathematical modeling of the processes taking place in the electro-pneumatic actuator of a robotic transmission. Analysis of the results of mathematical modeling allowed finding factors that give a competitive advantage in comparison with automated clutch control systems that are used for commercial purposes.
3 April 2018 in SAE International Journal of Advances and Current Practices in Mobility
This article describes experimental research results of the electropneumatic clutch control device for the mechanical transmission. The aim is to assess electropneumatic clutch control device characteristics to regulate both mechanical and robotic transmission. The feature of the clutch control system having the electropneumatic actuator on the basis of a power cylinder is the use of a control module that consists of an acceleration valve and two electropneumatic valves. A new structural relationship between the electropneumatic clutch control device elements on the basis of the new acceleration valve design is suggested. The assessment of mass and dimension parameters of well-known devices and this electropneumatic clutch control device is provided. A new approach to choose automated clutch control system parameters taking into account the relay electropneumatic control system operation features is suggested. The experimental data that enable us to determine the clutch control actuator rational parameters are given. Using mathematical modelling methods, the automated clutch control system rational parameters are determined. The comparative experimental research results allow us to determine the factors that give competitive advantages in comparison with clutch control electromechanical devices existing diagrams. Analysis of the comparative research of clutch control systems indicates that the system operation speed and precision with the suggested electropneumatic actuator are at the level of production systems. At the same time, the use of the control module, which consists of an acceleration valve and two electropneumatic valves, considerably simplifies the proposed design and reduces its cost.
15 September 2020 in SAE International Journal of Advances and Current Practices in Mobility
The article presents studies of the operating process of the pneumatic engine, that can be installed on small vehicles as main or auxiliary power generating system. The aim is to assess the possibility of converting an internal combustion engine into a pneumatic engine capable of moving a vehicle with a small mass in urban settings with dense traffic flows using mathematical modelling. The behaviour in the operating processes of the engine under study has been performed by the computational method and verified experimentally at the installation created in the laboratory of the ICE department in Kharkiv National Automobile and Highway University. The computational technique in question differs from the existing ones because it is based on a dynamic model of an internal combustion engine. The developed pneumatic engine was mounted on the stand for determining its power, developed torque, compressed air consumption, pressure in its cylinders and the temperature of heating the engine. The inlet pressure ranged from 0.6 to 1.1 MPa. The results of testing the pneumatic engine showed that when using a spool-type air distributor without heating, it could reach a rate power of Nе = 6.22 kW with a specific flow rate of compressed air gе = 91.45 kg/(kW ∙ h). A comparison of the calculated «Р-V diagram» with the diagram obtained experimentally with corresponding parameters of pressure and temperature at the inlet to the sleeve valve has been performed. The difference in the results of theoretical and experimental studies is less than 5%.
In the article the mathematical model of the vehicle motion with elastic tires, which describes the phases of the initial rectilinear motion on the longitudinal slope of the road is shown. The mathematical model is valid for vehicle with two axles, one of which is driving axel and provided that the stopped vehicle on a slope is kept from rolling only by braking the non-driving axle. The aim of the study is to determine the equations to describe the process of vehicle initial rectilinear motion during moving uphill, which take into account the tires deformation energy on the stationary vehicle braking wheels. The presented equations described in the article are reflect the dynamic state of the stationary vehicle on a slope and the phase of its initial moving off uphill after brining the engine torque through the transmission to the wheels of the drive axle. The system of equations describing the vehicle dynamic behavior after brining torque to the drive wheels takes into account their false slip. The system of equations is obtained from the general dynamic equation in the form of balance of the elementary work of external forces and moments with the absence of external slipping of the driving wheels. The mathematical model of the vehicle initial rectilinear motion on a longitudinal slope of a highway described in the article can be used in theoretical basis for analyzing and synthesizing control algorithms for automatic driver assistance systems during vehicle initial motion.