5 October 2018 in SAE International Journal of Advances and Current Practices in Mobility
New solutions for actual problems of determination the efficient distribution of braking forces between the axles of the vehicle, and the stability and drivability of two-axles vehicles at service braking are received in the thesis. It permitted for the first time to determine the Law of distribution of the braking forces between the axles, that ensuring straight-running stability of two-axle vehicle at service braking, to obtain the ideal characteristics for the braking system of two-axle vehicle at service braking and to determine possible values for the distribution of braking force on the front axle. The drivability criterion at service braking obtained further development; it is offered to use boundary at gripping front or rear wheels angular vehicle acceleration on the road. The application of the stability coefficient as one of the criteria for service braking efficiency allowed to determine the ideal, as for preserving the road-holding ability, Law of distribution of the braking forces between the axles. Despite the idea, if the vehicle deceleration is increased at service braking, the ideal coefficient of braking force distribution on the front axle should be decreased, but not be increased. At small decelerations, the given coefficient can be equal to one (rear wheels are not braked), and at the maximum decelerations - we should take into account the values that correspond to retain the front and rear wheels on the blocking limit. The area of rational values of the coefficient of braking force distribution on the front axle, limited by the curves of the ideal distribution of braking forces at service braking and limit values of the adhesion coefficient, and by straight line of the ideal distribution of braking forces at emergency braking are determined. The limit values of the vehicle deceleration at service braking are determined. If the limit values are lower than the given ones, it is necessary to carry out braking only with the front wheels brakes. The obtained ideal characteristics of the two-axles braking system allow to estimate braking dynamics at emergency and service braking on roads with different coefficient of adhesion. With constant distribution of braking forces between the axles the deceleration area boundaries in which the vehicle can retain the road-holding ability at service braking are defined. To assess the impact of disturbances on the road-holding ability of the vehicle at service braking, a new criterion, the coefficient of disturbing action is offered. If the criterion value does not exceed the stability coefficient, the vehicle is stable, otherwise it loses its stability.
15 January 2019 in SAE International Journal of Advances and Current Practices in Mobility
The article deals with the analysis of one of the methods of selecting rational parameters of automated clutch control system for robotic transmission. The objective is to select rational parameters of automated clutch control system for robotic transmission, equipped with electropneumatic actuating mechanism on the basis of mathematical simulation. The depicted mathematical simulation of the clutch control system is characterized by the possibility to coordinate the algorithm of control unit with the dynamic processes in the execution device. The new functional interrelations between the elements of the electro-pneumatic actuator are mathematically described. The way to the selection of rational parameters of an automated control system for clutch is recommended; the selection taking into account the features of the electro-pneumatic actuator. Using the mathematical modeling method, rational control parameters of the automated clutch control system are determined. Based on comparative experimental researches, an inaccuracy is calculated for the mathematical modeling of the processes taking place in the electro-pneumatic actuator of a robotic transmission. Analysis of the results of mathematical modeling allowed finding factors that give a competitive advantage in comparison with automated clutch control systems that are used for commercial purposes.
3 April 2018 in SAE International Journal of Advances and Current Practices in Mobility
This article describes experimental research results of the electropneumatic clutch control device for the mechanical transmission. The aim is to assess electropneumatic clutch control device characteristics to regulate both mechanical and robotic transmission. The feature of the clutch control system having the electropneumatic actuator on the basis of a power cylinder is the use of a control module that consists of an acceleration valve and two electropneumatic valves. A new structural relationship between the electropneumatic clutch control device elements on the basis of the new acceleration valve design is suggested. The assessment of mass and dimension parameters of well-known devices and this electropneumatic clutch control device is provided. A new approach to choose automated clutch control system parameters taking into account the relay electropneumatic control system operation features is suggested. The experimental data that enable us to determine the clutch control actuator rational parameters are given. Using mathematical modelling methods, the automated clutch control system rational parameters are determined. The comparative experimental research results allow us to determine the factors that give competitive advantages in comparison with clutch control electromechanical devices existing diagrams. Analysis of the comparative research of clutch control systems indicates that the system operation speed and precision with the suggested electropneumatic actuator are at the level of production systems. At the same time, the use of the control module, which consists of an acceleration valve and two electropneumatic valves, considerably simplifies the proposed design and reduces its cost.
9 February 2018 in Science & Technique
В статье рассмотрен один из способов управления исполнительным механизмом автоматизированной системы управления сцеплением. На основе экспериментальных исследований предложены способ управления электропневматическим исполнительным устройством управления сцеплением с ускорительным клапаном, а также рациональные параметры автоматизированной системы управления сцеплением для роботизированной трансмиссии. Особенностью рассматриваемой системы является наличие в конструкции электропневматического исполнительного механизма управления сцеплением ускорительного клапана. Наличие новых связей требует корректировки способа управления исполнительным механизмом. Обосновано объединение широтно-импульсной модуляции с одиночными импульсами питания для управления электропневматическими клапанами. Определены количественные характеристики управляющих импульсов как для случая одиночных, так и в случае использования широтно-импульсной модуляции. Определена ошибка точности работы во время разных способов управления электропневматическим исполнительным устройством управления сцеплением роботизированной трансмиссии. Выделена отдельная зона широтно-импульсной модуляции, предназначенная для подавления начального гистерезиса при перемещении штока исполнительного устройства управления сцеплением. Предложен алгоритм работы системы управления сцеплением с учетом использования двух режимов работы электромагнитных клапанов. Представлена графическая интерпретация алгоритма управления сцеплением, дающая представление о расположении зон подачи постоянного сигнала на электромагнитный клапан, а также зон работы электромагнитного клапана в режиме широтно-импульсной модуляции. В алгоритме управления усилителем предусмотрен режим гарантированного сброса давления из пневматического цилиндра после отпускания педали сцепления при условии использования двух нормально закрытых электромагнитных клапанов. Такая конфигурация электропневматической системы управления сцеплением позволяет задействовать систему аварийного выключения сцепления при отсутствии электропитания. Приведены опорный алгоритм фильтрации массива данных, поступающих от датчика обратной связи, а также численные значения запаздывания, вызванного наличием фильтра.
15 September 2019 in SAE International Journal of Advances and Current Practices in Mobility
One of the reasons for the large number of road accidents on highways in Ukraine [1] is the instability of the braking properties due to the unstable characteristics of the brake mechanisms’ friction pairs. The manufacturer produces new automobiles with installed brake pairs (brake pads and their counter bodies), which have passed long-term tests for the stability of the friction coefficient and braking forces distribution of between the axles. This ensures the compatibility of the friction pairs characteristics for front and rear brake mechanisms according to the criteria of heat resistance. During operation, instead of worn-out brake pads, brake discs and drums, drivers can purchase new ones, manufactured as spare parts. However, in the well-known literature there are no methods that allow to check the compatibility of the friction pairs characteristics for front and rear brake mechanisms according to the criteria of heat resistance. In the article a method for choosing a set of friction pairs of brake mechanisms for passenger car during operation is proposed. Assessment of the compatibility of the friction pairs characteristics for front and rear brake mechanisms was carried out according to the criteria of heat resistance.
29 May 2021 in Automobile Transport
Problem. A malfunction of the service braking system of a wheeled vehicle (CTS) significantly affects road safety, especially when operating multi-axle vehicles with large masses. One of the ways to increase the level of road safety of multi-axle vehicles, when braking them using a spare (emergency) braking system, is the introduction of automated adaptive braking systems into the design of the brake drive of vehicles. The definition of the limits of the use of the adaptive braking system on vehicles with many axles is almost not disclosed in the scientific and technical literature, therefore, the issue of using such a system on vehicles with a large number of axles requires additional research. Purpose. The purpose of this work is to develop a simulation model for adaptive control of the braking process of a multi-axle vehicle using a spare (emergency) braking system, taking into account the simulation of the dynamics of the drive and the variability of the adhesion properties between the tire of the vehicle wheel and the road surface. Methodology. To achieve this goal, it is necessary to develop a simulation model of the brake drive in an adaptive mode, implement a model of the interaction of the tire with the road surface, and implement a model of the braking dynamics of a multi-axle vehicle in the event of a malfunction of its service brake system. Originality. The proposed key criterion (Kr) for changing the throttle section in electro-pneumatic pressure modulators, which provide adaptive air inlet or outlet from the corresponding brake chambers of the drive, during simulation, made it possible to simulate the operation of the drive circuits in the adaptive mode. It has been established that, depending on the potential for the realization of the adhesion between the tires of automobile wheels and the road surface, the pressure in the electro-pneumatic brake drive with its adaptive regulation can be increased by no more than 0.04 MPa.