The aim of the present work is to study the effect of different activation methods for the production of a biomass-based activated carbon on the CO and CH adsorption. The influence of the activation method on the adsorption uptake was studied using three activated carbons obtained by different activation methods (H PO chemical activation and H O and CO physical activation) of olive stones. Methane and carbon dioxide pure gas adsorption experiments were carried out at two working temperatures (303.15 and 323.15 K). The influence of the activation method on the adsorption uptake was studied in terms of both textural properties and surface chemistry. For the three adsorbents, the CO adsorption was more important than that of CH . The chemically-activated carbon presented a higher specific surface area and micropore volume, which led to a higher adsorption capacity of both CO and CH . For methane adsorption, the presence of mesopores facilitated the diffusion of the gas molecules into the micropores. In the case of carbon dioxide adsorption, the presence of more oxygen groups on the water vapor-activated carbon enhanced its adsorption capacity.
11 March 2017 in Environmental Science and Pollution Research
Bioprocesses, such as biofiltration, are commonly used to treat industrial effluents containing volatile organic compounds (VOCs) at low concentrations. Nevertheless, the use of biofiltration for indoor air pollution (IAP) treatment requires adjustments depending on specific indoor environments. Therefore, this study focuses on the convenience of a hybrid biological process for IAP treatment. A biofiltration reactor using a green waste compost was combined with an adsorption column filled with activated carbon (AC). This system treated a toluene-micropolluted effluent (concentration between 17 and 52 µg/m3), exhibiting concentration peaks close to 733 µg/m3 for a few hours per day. High removal efficiency was obtained despite changes in toluene inlet load (from 4.2 × 10−3 to 0.20 g/m3/hr), which proves the hybrid system’s effectiveness. In fact, during unexpected concentration changes, the efficiency of the biofilter is greatly decreased, but the adsorption column maintains the high efficiency of the entire process (removal efficiency [RE] close to 100%). Moreover, the adsorption column after biofiltration is able to deal with the problem of the emission of particles and/or microorganisms from the biofilter.
Purifying biogas by removing contaminants and carbon dioxide (CO2) to produce biomethane enhances its energy content, making it suitable as fuel and for injection into natural gas grids. Bamboo-derived adsorbents Bamboo-500 (pyrolyzed at 500 °C), Bamboo-700 (pyrolyzed at 700 °C), and Bamboo-A-900 (activated with CO2 at 900 °C) were synthesized and characterized to evaluate their performance for CO2 and CH4 adsorption. Increasing pyrolysis temperature from 500 °C to 700 °C and further CO2 activation at 900 °C enhanced adsorption capacities of CO2 and CH4 due to improved surface area and micropore structure. In this study, the novel Approximate Adsorption Performance Indicator (AAPI) approach is introduced, offering an efficient method for evaluating adsorbent performance, particularly in biogas upgrading. AAPI results suggest Bamboo-500 is suitable for biogas upgrading at very low pressures (<0.12 MPa) with low regeneration energy and acceptable CO2 capacity (1.9 ± 0.2 mol kg−1). However, Bamboo-A-900 excelled at medium and high pressures by its highest CO2 adsorption capacity (8.0 ± 0.3 mol kg−1) promoted by the high surface area (1220 m2g−1) and calcium oxide presence. Finally, Bamboo-A-900 shows promise for enhancing CO2 adsorption and biogas upgrading. Bamboo-derived adsorbents offer a sustainable solution for biogas upgrading, supporting Sustainable Development Goals by promoting clean energy transitions.
The preliminary selection of adsorbents for the separation of a gas mixture based on pure gas adsorption remains a critical challenge; thus, an approximate adsorption performance indicator (AAPI) was proposed for the initial evaluation of the adsorbents to separate the biogas main constituents (carbon dioxide/methane (CO2/CH4)) by studying their pure gas adsorption. Three samples derived from cocoa pod husk (CPH), namely Cabosse-500 (pyrolyzed at 500 °C), Cabosse-700 (pyrolyzed at 700 °C), and Cabosse-A-700 (activated with CO2 at 700 °C), were synthesized, characterized, and evaluated for the pure gases adsorption. This study presents an AAPI evaluation, which takes into account adsorption capacity, approximate selectivity, and heat of adsorption. Adsorption isotherms indicate the ability of the CPH family to selectively capture CO2 over CH4, as they have a high approximate selectivity (>1) thanks to their physical properties. Changing the pyrolysis temperature, activation methods, and varying the pressure can significantly change the choice of the most effective adsorbent; Cabosse-A-700 showed better performance than the other two in the low and high pressure range owing to its presence of micropores and mesopores, which enhances the CO2 adsorption and therefore the AAPI.