Transition metal hexacyanoferrate/microporous activated carbon composites were obtained using a simple successive impregnation approach. The effect of metal type (nickel, indium, or copper), and the carbon oxidation on the composite characteristics (porosity, metal structure, and particle size), as well as on the removal efficiency of cesium from aqueous solution was investigated. Successful formation of the desired metal hexacyanoferrate phase was achieved and the size of the metallic nanoparticles and their dispersion in the carbon network was found to depend on the metal type, with the indium and nickel-based materials exhibiting the smallest particle size distribution (< 10 nm). Adsorption tests performed under batch conditions demonstrate that the copper hexacyanoferrate/activated carbon composite present the highest cesium removal capacity from aqueous solution (74.7 mg·g−1) among the three studied metal-based nanocomposites. The carbon oxidation treatment leads to the increase in the number of functional groups to the detriment of the porosity but allows for an improvement in the Cs adsorption capacity. This indicates that the Cs adsorption process is governed by the carbon surface chemistry and not its porosity. Moreover, combining oxidized carbon support with copper hexacyanoferrate induces the highest cesium adsorption capacity (101.5 mg·g−1). This could be related to synergistic effects through two absorption mechanisms, i.e., a cation exchange mechanism of Cs with the metallic hexacyanoferrate phase and Cs adsorption via carbon oxygen surface groups, as demonstrated using X-ray photoelectron spectroscopy (XPS) analyses.
Although transition metal sulfides have prodigious potential for use as electrode materials because of their low electronegativities, their large volume changes inhibit broad application. Moreover, there is only limited knowledge of the ageing processes of these materials at the nanoscale. Herein, nano-C/FeS2 materials were prepared via one-pot syntheses from green biodegradable carbon precursors, followed by activation and sulfidation. The increased activation/sulfidation time led to an increase in the size of the nanoparticles (7 to 17 nm) and their aggregation, as well as in an increase in the specific surface area. The materials were then used as electrodes in 2-electrode symmetric supercapacitors with 2 M KOH. The activation process resulted in improved capacitance (60 F g−1 at 0.1 A g−1) and rate capability (36%) depending on the composite porosity, conductivity, and size of the FeS2 particles. The ageing of the FeS2 nanoparticles was investigated under air, and a progressive transformation of the nano-FeS2 into hydrated iron hydroxy sulfate with a significant morphological modification was observed, resulting in drastic decreases in the capacitance (70%) and retention. In contrast, the ageing of nano-FeS2 during cycling led to the formation of a supplementary iron oxyhydroxide phase, which contributed to the enhanced capacitance (57%) and long-term cycling (132% up to 10,000 cycles) of the device.
The preliminary selection of adsorbents for the separation of a gas mixture based on pure gas adsorption remains a critical challenge; thus, an approximate adsorption performance indicator (AAPI) was proposed for the initial evaluation of the adsorbents to separate the biogas main constituents (carbon dioxide/methane (CO2/CH4)) by studying their pure gas adsorption. Three samples derived from cocoa pod husk (CPH), namely Cabosse-500 (pyrolyzed at 500 °C), Cabosse-700 (pyrolyzed at 700 °C), and Cabosse-A-700 (activated with CO2 at 700 °C), were synthesized, characterized, and evaluated for the pure gases adsorption. This study presents an AAPI evaluation, which takes into account adsorption capacity, approximate selectivity, and heat of adsorption. Adsorption isotherms indicate the ability of the CPH family to selectively capture CO2 over CH4, as they have a high approximate selectivity (>1) thanks to their physical properties. Changing the pyrolysis temperature, activation methods, and varying the pressure can significantly change the choice of the most effective adsorbent; Cabosse-A-700 showed better performance than the other two in the low and high pressure range owing to its presence of micropores and mesopores, which enhances the CO2 adsorption and therefore the AAPI.