A DC-DC power converter based on a two-phase synchronous buck converter that reproduces single-carrier digital modulation schemes by controlling the first switching harmonic of the output voltage ripple is presented in this work. The DC-DC power converter carries out both the lighting and the transmission functionalities of Visible Light Communication (VLC) transmitters. Control of both the amplitude and the phase of sinusoidal currents injected towards High-Brightness LEDs (HB-LEDs) enables the use of efficient modulation schemes such as Quadrature Amplitude Modulation (QAM), Carrier-less Amplitude and Phase modulation (CAP), Amplitude-Shift Keying (ASK) and Phase-Shift Keying (PSK). These modulation schemes achieve higher spectral efficiency (i.e. more data can be transmitted using the same bandwidth) than previously proposed modulation schemes performed by VLC transmitters based on the use of DC-DC power converters. To the author's knowledge, the ratio between the bit rate achieved and the switching frequency of the DC-DC power converter presented in this paper is the highest that can be found in literature.

Wide bandgap devices such as GaN HEMTs are a promising technology in the field of Power Electronics. Due to the physical properties of the Gallium nitride and the device design, they can outperform their Silicon counterparts for the design of highly efficient power switching converters. However, its design should face certain effects that can diminish its performance. One of such effect is the degradation mechanism known as dynamic onresistance (dynamic RON,), being its mitigation one of the main objectives in the design of the device. In this paper, a circuit is proposed for assessing if this effect is present in GaN transistors in power electronics applications. The circuit allows testing the GaN HEMTs with different stress voltages and times maintaining the desired current level, and allows for repeating the test in successive switching pulses, with adjustable switching frequency and duty cycle, always with the same current, mimicking a real power electronics application.

The continuous demand of increasing data rates provided by wireless communication systems is contributing to saturating the RF spectrum. Visible Light Communication (VLC) systems aim to alleviate this congestion by using the visible light spectrum. These systems have been proposed to make use of High-Brightness LEDs (HB-LEDs) not only for lighting, but also for transmitting information by rapidly changing the intensity of the emitted light. A critical issue is that VLC requires a fast HB-LED driver in order to reproduce the target light intensity waveforms, which can include components of several MHz. Consequently, the HB-LED drivers proposed to date are based on the use of an RF Power Amplifier (RFPA). These devices provide the required speed, but suffer from very high power losses. To overcome this drawback, different solutions based on the use of fast-response DC/DC converters are presented in this paper. Several DC/DC converters, either to be used instead of an RFPA or to help an RFPA to achieve high efficiency, are thus analysed. The proposed HB-LED drivers enable the implementation of VLC transmitters without sacrificing one of the most important advantages of HB-LED lighting, namely its high power efficiency.

The Ripple Modulation (RM) is a technique that provides a variable output voltage by using the output voltage ripple of a Switching-Mode Power Converter (SMPC). It was proposed to reproduce the communication signal of a Visible Light Communication (VLC) transmitter, thus avoiding the use of power inefficient Linear Power Amplifiers (LPAs). However, the RM has a major drawback: it has not been reported how to reproduce Multi-Carrier Modulation (MCM) schemes, which are the preferred modulation schemes due to their high performance in wireless communications. In this work, it is demonstrated that the RM can be used to reproduce MCM schemes by considering the envelope and the instantaneous phase of the communication signal. Moreover, the control system of the power stage is described in detailed, explaining how to modulate both the width and the phase of the gate signals, the calculation of the phase-shift that is required for tracking the envelope, etc.

Visible light communication (VLC) has gained relevance during the last few years. It consists in using high-brightness LEDs (HB-LEDs) both for lighting and transmitting information by changing the light intensity rapidly. However, there are some bottlenecks that are slowing down the deployment of this technology. One of the most important problems is that the HB-LED drivers proposed for addressing high data rates in VLC achieve poor power efficiency. Since these HB-LED drivers must be able to reproduce fast current waveforms, the use of linear power amplifiers has been adopted, which clearly damages the power efficiency of HB-LED lighting. In order to alleviate this problem, an HB-LED driver made up of two DC-DC power converters is presented in this work. One of them is responsible for performing the communication functionality by operating at high switching frequency (10 MHz), whereas the second converter fulfills the illumination functionality by ensuring a certain biasing point. The split of the power allows us to minimize the power delivered by the fast-response DC-DC power converter, which suffers from high switching losses. Thus, the overall efficiency can be maximized for each particular communication scenario and for scenarios with changing conditions (i.e., mobile transmitter and/or receiver, presence of mobile obstacles, etc.). In this sense, how the lighting level and the communication signal power affect both the power efficiency and the communication efficiency is deeply analyzed in the experimental section. The implemented prototype achieves an overall efficiency around 90%. In addition, the proposed VLC transmitter is able to reproduce a wide range of digital modulation schemes, including the preferred one for wireless communications: orthogonal frequency division multiplexing.

Visible light communication (VLC) based on solid-state lighting (SSL) is a promising option either to supplement or to substitute existing radio frequency (RF) wireless communication in indoor environments. VLC systems take advantage of the fast modulation of the visible light that light emitting diodes (LEDs) enable. The switching-mode dc-to-dc converter (SMC_dc-dc) must be the cornerstone of the LED driver of VLC transmitters in order to incorporate the communication functionality into LED lighting, keeping high power efficiency. However, the new requirements related to the communication, especially the high bandwidth that the LED driver must achieve, converts the design of the SMC_dc-dc into a very challenging task. In this work, three different methods for achieving such a high bandwidth with an SMC_dc-dc are presented: increasing the order of the SMC_dc-dc output filter, increasing the number of voltage inputs, and increasing the number of phases. These three strategies are combinable and the optimum design depends on the particular VLC application, which determines the requirements of the VLC transmitter. As an example, an experimental VLC transmitter based on a two-phase buck converter with a fourth-order output filter will demonstrate that a bandwidth of several hundred kilohertz (kHz) can be achieved with output power levels close to 10 W and power efficiencies between 85% and 90%. In conclusion, the design strategy presented allows us to incorporate VLC into SSL, achieving high bit rates without damaging the power efficiency of LED lighting.