The piecewise linear model has traditionally been used to calculate switching losses in switching mode power supplies due to its simplicity and good performance. However, the use of the latest low voltage power MOSFET generations and the continuously increasing range of switching frequencies have made it necessary to review this model to account for the parasitic inductances that it does not include. This paper presents a complete analytical switching loss model for power MOSFETs in low voltage switching converters that includes the most relevant parasitic elements. It clarifies the switching process, providing information about how these parasitics, especially the inductances, determine switching losses and hence the final converter efficiency. The analysis presented in this paper yields two different types of possible switching situations: capacitance-limited switching and inductance-limited switching. This paper shows that, while the piecewise linear model may be applied in the former, the proposed model is more accurate for the latter. Carefully-obtained experimental results, described in detail, support the analytical results presented.

Wireless communication transmitters have very low efficiencies due to the use of linear radiofrequency power amplifiers. Several techniques have been proposed over the years to improve the efficiency of these systems. One of the most promising is called the envelope tracking technique, which is based on using a fast switching mode power supply to provide a varying voltage to the power amplifier that tracks the envelope of the transmitted signal. The amplifier can, thus, operate continuously near its theoretical maximum efficiency, greatly improving the overall efficiency of the communication system. This paper proposes a multilevel digitally controlled power supply suitable for this application. It is shown to perform very well, achieving very high efficiency, high-output power capability and tracking bandwidths above 50 kHz. This paper also shows that the proposed system is able to produce a 15% overall increase in efficiency in a complete envelope tracking system.

A DC-DC power converter based on a two-phase synchronous buck converter that reproduces single-carrier digital modulation schemes by controlling the first switching harmonic of the output voltage ripple is presented in this work. The DC-DC power converter carries out both the lighting and the transmission functionalities of Visible Light Communication (VLC) transmitters. Control of both the amplitude and the phase of sinusoidal currents injected towards High-Brightness LEDs (HB-LEDs) enables the use of efficient modulation schemes such as Quadrature Amplitude Modulation (QAM), Carrier-less Amplitude and Phase modulation (CAP), Amplitude-Shift Keying (ASK) and Phase-Shift Keying (PSK). These modulation schemes achieve higher spectral efficiency (i.e. more data can be transmitted using the same bandwidth) than previously proposed modulation schemes performed by VLC transmitters based on the use of DC-DC power converters. To the author's knowledge, the ratio between the bit rate achieved and the switching frequency of the DC-DC power converter presented in this paper is the highest that can be found in literature.

This paper presents the introduction of problem-based learning (PBL) in a power electronics course at the University of Oviedo, Gijón, Spain, by means of two practical projects: the design and construction of a switching-mode power supply (SMPS) prototype and the static study of a dc-dc converter topology. The goal of this innovation was for students to apply in practice the knowledge they had acquired in theory classes. PBL is known to be a motivating, problem-centered teaching method that brings the real professional world closer to the student. The instructors thus considered PBL to be the most suitable methodology to obtain the desired results. The underlying methodology, task planning, and assessment of these projects will be presented. Furthermore, the influence of the introduction of PBL in practical sessions versus the traditional teaching method will be discussed. Finally, the instructors' reflections and conclusions regarding the application of PBL in this course from 2007-2009 will be presented.

In recent years, there has been a great deal of focus on the development of fast and efficient dc/dc converters in an effort to follow the envelope of communication signals for increasing the efficiency of RF power amplifiers by using techniques such as envelope tracking and envelope elimination and restoration. However, the bandwidth and slew rate required by modern communication signals are higher than the maximum ones achievable by switching dc/dc converters made for this purpose. The slew rate of these switching dc/dc converters can be improved by combining it with the use of a linear stage, thus establishing a trade-off between slew rate and overall efficiency. This paper presents a simple way of combining the use of both a switching dc/dc converter, the multiple input buck converter, and a linear stage to obtain slew rates above 100 V/μs, with a moderate decrease in the overall efficiency [81% efficiency tracking the envelope of an enhanced data rates for GSM evolution (EDGE) standard signal]. Finally, a prototype of the complete system (including the digital control for both stages) is presented in this paper.

The use of techniques such as envelope tracking (ET) and envelope elimination and restoration (EER) can improve the efficiency of radio frequency power amplifiers (RFPA). In both cases, high-bandwidth DC/DC converters called envelope amplifiers (EA) are used to modulate the supply voltage of the RFPA. This paper addresses the analysis and design of a modified two-phase Buck converter optimized to operate as EA. The effects of multiphase operation on the tracking capabilities are analyzed. The use of a fourth-order output filter is proposed to increase the attenuation of the harmonics generated by the PWM operation, thus allowing a reduction of the ratio between the switching frequency and the converter bandwidth. The design of the output filter is addressed considering envelope tracking accuracy and distortion caused by the side bands arising from the nonlinear modulation process. Finally, the proposed analysis and design methods are supported by simulation results, as well as demonstrated by experiments obtained using two 100-W, 10-MHz, two-phase Buck EAs capable of accurately tracking a 1.5-MHz bandwidth OFDM signal.