The continuous demand of increasing data rates provided by wireless communication systems is contributing to saturating the RF spectrum. Visible Light Communication (VLC) systems aim to alleviate this congestion by using the visible light spectrum. These systems have been proposed to make use of High-Brightness LEDs (HB-LEDs) not only for lighting, but also for transmitting information by rapidly changing the intensity of the emitted light. A critical issue is that VLC requires a fast HB-LED driver in order to reproduce the target light intensity waveforms, which can include components of several MHz. Consequently, the HB-LED drivers proposed to date are based on the use of an RF Power Amplifier (RFPA). These devices provide the required speed, but suffer from very high power losses. To overcome this drawback, different solutions based on the use of fast-response DC/DC converters are presented in this paper. Several DC/DC converters, either to be used instead of an RFPA or to help an RFPA to achieve high efficiency, are thus analysed. The proposed HB-LED drivers enable the implementation of VLC transmitters without sacrificing one of the most important advantages of HB-LED lighting, namely its high power efficiency.

The Ripple Modulation (RM) is a technique that provides a variable output voltage by using the output voltage ripple of a Switching-Mode Power Converter (SMPC). It was proposed to reproduce the communication signal of a Visible Light Communication (VLC) transmitter, thus avoiding the use of power inefficient Linear Power Amplifiers (LPAs). However, the RM has a major drawback: it has not been reported how to reproduce Multi-Carrier Modulation (MCM) schemes, which are the preferred modulation schemes due to their high performance in wireless communications. In this work, it is demonstrated that the RM can be used to reproduce MCM schemes by considering the envelope and the instantaneous phase of the communication signal. Moreover, the control system of the power stage is described in detailed, explaining how to modulate both the width and the phase of the gate signals, the calculation of the phase-shift that is required for tracking the envelope, etc.

Visible light communication (VLC) has gained relevance during the last few years. It consists in using high-brightness LEDs (HB-LEDs) both for lighting and transmitting information by changing the light intensity rapidly. However, there are some bottlenecks that are slowing down the deployment of this technology. One of the most important problems is that the HB-LED drivers proposed for addressing high data rates in VLC achieve poor power efficiency. Since these HB-LED drivers must be able to reproduce fast current waveforms, the use of linear power amplifiers has been adopted, which clearly damages the power efficiency of HB-LED lighting. In order to alleviate this problem, an HB-LED driver made up of two DC-DC power converters is presented in this work. One of them is responsible for performing the communication functionality by operating at high switching frequency (10 MHz), whereas the second converter fulfills the illumination functionality by ensuring a certain biasing point. The split of the power allows us to minimize the power delivered by the fast-response DC-DC power converter, which suffers from high switching losses. Thus, the overall efficiency can be maximized for each particular communication scenario and for scenarios with changing conditions (i.e., mobile transmitter and/or receiver, presence of mobile obstacles, etc.). In this sense, how the lighting level and the communication signal power affect both the power efficiency and the communication efficiency is deeply analyzed in the experimental section. The implemented prototype achieves an overall efficiency around 90%. In addition, the proposed VLC transmitter is able to reproduce a wide range of digital modulation schemes, including the preferred one for wireless communications: orthogonal frequency division multiplexing.

Visible light communication (VLC) based on solid-state lighting (SSL) is a promising option either to supplement or to substitute existing radio frequency (RF) wireless communication in indoor environments. VLC systems take advantage of the fast modulation of the visible light that light emitting diodes (LEDs) enable. The switching-mode dc-to-dc converter (SMC_dc-dc) must be the cornerstone of the LED driver of VLC transmitters in order to incorporate the communication functionality into LED lighting, keeping high power efficiency. However, the new requirements related to the communication, especially the high bandwidth that the LED driver must achieve, converts the design of the SMC_dc-dc into a very challenging task. In this work, three different methods for achieving such a high bandwidth with an SMC_dc-dc are presented: increasing the order of the SMC_dc-dc output filter, increasing the number of voltage inputs, and increasing the number of phases. These three strategies are combinable and the optimum design depends on the particular VLC application, which determines the requirements of the VLC transmitter. As an example, an experimental VLC transmitter based on a two-phase buck converter with a fourth-order output filter will demonstrate that a bandwidth of several hundred kilohertz (kHz) can be achieved with output power levels close to 10 W and power efficiencies between 85% and 90%. In conclusion, the design strategy presented allows us to incorporate VLC into SSL, achieving high bit rates without damaging the power efficiency of LED lighting.

Envelope tracking is a well-known RF technique that alleviates the efficiency problem of linear power amplifiers used in wireless communication transmitters. It consists in varying the supply voltage of the amplifier, which is commonly constant, according to the envelope of the communication signal. Therefore, a switching-mode power converter with a bandwidth of several megahertz is required to perform the fast voltage changes needed for tracking the envelope properly. Another important requirement is that the converter needs to be able to achieve high efficiency not only at peak output power, but also at low output power because it operates in that power range most of the time due to the characteristics of modern communication signals. Taking into account these requirements, the design of the converter is very challenging, especially in the case of base stations, where higher power levels are reached by means of higher voltage levels. As a result, transistors with low breakdown voltages (20–30 V), which offer the highest speed, cannot be used in the converter. In this article, a novel multilevel converter able to use transistors with low breakdown voltages is proposed to alleviate that problem. Moreover, it shows a better switching behavior than the previously proposed multilevel converters, thus reducing the switching losses and, consequently, increasing the efficiency. In order to experimentally validate the proposed topology, a 73-W prototype with a switching frequency of 8 MHz was built. The efficiency is 94% and 81.7% at peak output power and at one-tenth of peak output power, respectively.