The paper describes the effect of the addition of alumina nanofibers on the mechanical properties of the epoxy resin. Alumina nanofibers functionalized with epoxypropyl functional groups are used in this work. The dependence of the mechanical characteristics on the amount of the additive, as well as the features of its distribution in the material, is investigated. In the work, nanocomposites were obtained, which are epoxy resin with aluminum oxide nanofibers. The mechanical properties of the samples were studied by bending tests and differential mechanical analysis (DMA). It has been shown that the addition of alumina nanofibers leads to an increase in ultimate flexural strength. The maximum of this increase is near the percolation threshold of alumina nanofibers in epoxy resin. With the addition of 0.2% alumina nanofibers, the ultimate flexural strength increases from 41 to 71 MPa. It is shown that after exceeding the percolation threshold of nanofibers, the ultimate strength decreases. In this case, the elastic modulus increases from 0.643 to 0.862 GPa. DMA is shown that the glass transition temperature decreases with increasing amount of the additive. This indicates a decrease in the molecular weight of the polymer. By implication, this suggests that the hardener connects the epoxypropyl functional groups on the nanofibers and the epoxy groups in the resin, and as a result of this process, the nanofibers become natural polymer chain length limiters. The data obtained from mechanical testing and differential mechanical analysis can be used to strengthen epoxy resins in polymer composite materials and molding compositions.
Nowadays, the Internet of Things (IOT), electronics, and neural interfaces are becoming an integral part of our life. These technologies place unprecedentedly high demands on materials in terms of their mechanical and electrical properties. There are several strategies for forming conductive layers in such composites, e.g., volume blending to achieve a percolation threshold, inkjet printing, lithography, and laser processing. The latter is a low-cost, environmentally friendly, scalable way to produce composites. In our work, we synthesized AgNW and characterized them using Ultraviolet-visible spectroscopy (UV-vis), Transmission electron microscopy (TEM), and Selective area electron diffraction (SAED). We found that our AgNW absorbed in the UV-vis range of 345 to 410 nm. This is due to the plasmon resonance phenomenon of AgNW. Then, we applied the dispersion of AgNW on the surface of the polymer substrate, dried them and we got the films of AgNW.. We irradiated these films with a 432 nm laser. As a result of the treatment, we observed two processes. The first one was the sintering and partial melting of nanowires under the influence of laser radiation, as a consequence of which, the sheet resistance dropped more than twice. The second was the melting of the polymer at the interface and the subsequent integration of AgNW into the substrate. This allowed us to improve the adhesion from 0–1 B to 5 B, and to obtain a composite capable of bending, with radius of 0.5 mm. We also evaluated the shielding efficiency of the obtained composites. The shielding efficiency for 500–600 nm thick porous film samples were 40 dB, and for 3.1–4.1 µm porous films the shielding efficiency was about 85–90 dB in a frequency range of 0.01–40 GHz. The data obtained by us are the basis for producing flexible electronic components based on AgNW/PET composite for various applications using laser processing methods.
As part of the work, the chemical interaction of finely ground glass (~1 μm), calcium oxide, and water was studied. It is shown that an increase in the fineness of grinding makes it possible to abandon autoclave hardening in the production of products on a hydrosilicate binder. The study of chemical interaction was carried out by calculating the thermodynamic equilibrium and was also confirmed by XRD analysis. DTA analysis showed that an increase in the treatment temperature leads to an increase in the proportion of the reacted phase at the first stage. Subsequently, phase formation is associated with the presence of CaO. The carrier of strength characteristics is the CaO×2SiO2×2H2O phase. The selection and optimization of the composition make it possible to obtain a high-strength glass concrete material with a strength of about 110 MPa. The micrographs of the obtained samples correspond to classical hydrosilicate systems.
For the first time, an environmentally friendly waste-free closed cycle for the formation of EMI shielding materials that are promising for 5G communications is considered. Based on the proposed closed technological cycle, two types of EMI shielding materials have been obtained; both materials have significant prospects for signal shielding in all ranges that are allocated in different countries for 5G communication. The first type of materials are transparent conductive meshes with a transparency of more than 80% and with a shielding efficiency of more than 40 dB in the S and L bands and about 30 dB in the K and Ka bands. The study of signal reflection characteristics in the S, L, C, K and Ka bands showed the promise of using these materials as transparent 5G signal reflectors. The reflection coefficient in all considered ranges is above 90% (-0.5 dB). The second type of shielding material are continuous silver micro caps films characterized by a shielding efficiency of 90.1 dB at a thickness of 6.2±1.2 µm. We have also shown that silver micro caps can separate into silver flakes and ribbons when sonicated. These materials can also be used to produce EMI shielding coatings and composites. A detailed analysis of the shielding properties showed that each type of materials obtained in a closed technological cycle is comparable with the best literature results and significantly wins in terms of cost.
In this work, nanocomposite photoelectrodes of the TiO2/ Au composition were manufactured, in which the size of plasmonic Au nanoparticles was varied, and the morphology of the TiO2 layer, depending on the thickness, changed from an island to a continuous layer. The influence of the morphology of plasmonic Au nanoparticles and the TiO2 layer on the optical and photoelectrochemical characteristics of hybrid photoelectrodes was studied. It has been shown that continuous coating of Au nanoparticles with a TiO2 layer (layer thickness 10 and 15 nm) leads to a decrease in the photoelectric response, and the decrease in photocurrent density and photoconversion efficiency decreases in proportion to the thickness of the TiO2 layer. The indicated drop in characteristics when plasmonic particles are located under the TiO2 layer is presumably associated with the scattering and recombination of charge carriers in the semiconductor layer. The best performance was shown by a system in which large Au nanoparticles (10 nm) are coated with a 5 nm thick layer of titanium dioxide; in this geometry, Au nanoparticles are decorated with TiO2 nanoparticles, as a result of which the photoelectrode-electrolyte interface has a more complex structure.