Kálmán Vad

Dr. Kálmán Vad

orcid

Research Focus & Metrics

Academic Career Length

32Years (1995-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 October 2002 in Physical Review B
Verified
Journal Article
Closed access
PDF file
FPF. Portier
F. Portier
GKG. Kriza
G. Kriza
BSB. Sas
B. Sas
LKL. F. Kiss
L. F. Kiss
IPI. Pethes
I. Pethes
FWF. I. B. Williams
F. I. B. Williams
Nonlinear transport in the low-temperature vortex glass state of single crystal Bi2Sr2CaCu2O8 has been investigated over long times (up to two weeks) with fast current pulses driven along the a−b plane. It is found that at low temperature and high magnetic field, both zero-field-cooled (ZFC) and field-cooled (FC) samples relax towards the same equilibrium state, which is much closer to the original ZFC state than to the FC state. The implication of this FC metastability for the vortex phase diagram is discussed in the context of previous measurements.

9 May 2016 in Metallurgical and Materials Transactions A
Verified
Journal Article
Closed access
PDF file
GLGabor Levai
Gabor Levai
MGMelinda Godzsák
Melinda Godzsák
TTTamás I. Török
Tamás I. Török
JHJozsef Hakl
Jozsef Hakl
VTViktor Takáts
Viktor Takáts
GKGeorge Kaptay
George Kaptay

10 January 2025 in Lubricants
Verified
Journal Article
Open access
PDF file
Ádám István SzabóÁdám István Szabó
Ádám István Szabó
Attila CsíkAttila Csík
Attila Csík
TFTamás Fodor
Tamás Fodor
KVKálmán Vad
Kálmán Vad
MMMárk Marsicki
Márk Marsicki
Álmos Dávid TóthÁlmos Dávid Tóth
Álmos Dávid Tóth
Nanoparticles exhibit diverse effects when added as additives to oily medium, enhancing tribological properties and surface characteristics. Studies have shown that many oxide ceramic nanoparticles improve friction and wear, while mixtures also demonstrate favorable tribological properties. This study explores the tribological effect of an yttria–silica (Y2O3, SiO2) nanoparticle mixture in a Group III base oil medium. The results reveal that the yttria–silica mixture significantly reduces friction (−8–17%), mean wear scar diameter (−32%), and wear volume (−94%), while increasing load-bearing capacity (+114%) by creating a durable boundary layer. Observations from scanning electron microscopy revealed the original surface is protected. EDX analyses highlight the boundary layer’s elemental composition, which is high in yttrium, silicon, and oxygen and found in higher areas. XRD analysis could not detect the yttria nanoparticle additive within the boundary layer, suggesting that it fragmented due to sliding stress, resulting in an amorphous structure for the new boundary layer. TEM imaging confirmed that the boundary layer thickness is 40–45 nm. These findings demonstrate significant potential for industrial applications in developing advanced, high-performance lubricants for demanding mechanical systems.

20 April 2011 in Defect and Diffusion Forum
Verified
Journal Article
Closed access
PDF file
Dezső BekeDezső Beke
Dezső Beke
Ákos LakatosÁkos Lakatos
Ákos Lakatos
GEG. Erdélyi
G. Erdélyi
AMA. Makovecz
A. Makovecz
GLG.A. Langer
G.A. Langer
Attila CsíkAttila Csík
Attila Csík
It was shown more recently in our Laboratory [1,2,3] that having a substrate/diffusant/thin-film/cap-layer structure (the thin film was typically several 10 nm thick, with the same order of magnitude of grain size; the refractory metal cap layer was used just to avoid the oxidation), first the diffusant atoms migrated very fast across the thin film and segregated at the film/cap-layer interface. The accumulated atoms at the film/cap layer interface form a secondary diffusion reservoir and atoms diffuse back to the layer. Later on, the thin film was gradually filled up with the diffusing atoms and composition depth profiles, determined by Secondary Neutral Mass Spectroscopy (SNMS), showed a maximum at the cap layer-thin film interface. The accumulated atoms at this interface formed a secondary diffusion reservoir and atoms diffused back to the layer. These observations can be interpreted supposing a bimodal grain boundary structure with different (fast and low) diffusivities. The observed grain boundary diffusion phenomena can be classified as C-type diffusion. The appearance of the peak observed at the cap layer interface can be used as a tool to determine the grain boundary diffusivity along the fast boundaries. Because the fast boundaries were saturated in the first stage of the process, this back-diffusion took place along the low-diffusivity boundaries only. Thus the SNMS depth-profiling is a good method to determine grain boundary diffusivities in a bimodal structure. In addition, from the overall impurity content inside the film the segregation can also be estimated, if the bulk solubility is low and the GB density is known. Numerical simulations of C-type GB diffusion in thin films with a bimodal structure confirmed that the interpretation of the result depicted above is reasonable [4]. In order to estimate roughly the GB diffusion data we determined the fast diffusivity using the first appearance method. The lower diffusivity was determined from the time evolution of the broadening of the diffusant/thin film interface. In addition both (slow and fast) diffusivities were also estimated from fitting numerical solutions obtained in [4] too.

28 December 2022 in Materials
Verified
Journal Article
Open access
PDF file
JCJuliusz Chojenka
Juliusz Chojenka
AZArkadiusz Zarzycki
Arkadiusz Zarzycki
MPMarcin Perzanowski
Marcin Perzanowski
MKMichal Krupinski
Michal Krupinski
TFTamás Fodor
Tamás Fodor
MMMarta Marszalek
Marta Marszalek
We describe the magnetic properties of thin iron films deposited on the nanoporous titanium oxide templates and analyze their dependance on nanopore radius. We then compare the results to a continuous iron film of the same thickness. Additionally, we investigate the evolution of the magnetic properties of these films after annealing. We demonstrate that the M(H) loops consist of two magnetic phases originating from the iron layer and iron oxides formed at the titanium oxide/iron interface. We perform deconvolution of hysteresis loops to extract information for each magnetic phase. Finally, we investigate the magnetic interactions between the phases and verify the presence of exchange coupling between them. We observe the altering of the magnetic properties by the nanopores as a magnetic hardening of the magnetic material. The ZFC-FC (Zero-field cooled/field cooled) measurements indicate the presence of a disordered glass state below 50 K, which can be explained by the formation of iron oxide at the titanium oxide-iron interface with a short-range magnetic order.

1 January 1995 in Measurement Science and Technology
Verified
Journal Article
Closed access
NHN Hegman
N Hegman
SMS Meszaros
S Meszaros
KVKálmán Vad
Kálmán Vad