Juan S. Cely

Dr. Juan S. Cely

Universidad Rey Juan Carlos, Madrid, Spain
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 August 2019 in Sensors
Verified
Journal Article
Open access
PDF file
Juan S. CelyJuan S. Cely
Juan S. Cely
Roque SaltarenRoque Saltaren
Roque Saltaren
GPGERARDO PORTILLA
GERARDO PORTILLA
Oz YakrangiOz Yakrangi
Oz Yakrangi
ABAlejandro Rodriguez Barroso
Alejandro Rodriguez Barroso
Hydrodynamic coefficients are essential for the development of underwater robots; in particular, for their design and navigation control. To obtain these coefficients, several techniques exist. These methods are usually experimental, but, more recently, some have been designed by a combination of experiments with computational methods based on Computational Fluid Dynamics (CFD). One method for obtaining the hydrodynamic coefficients of an ROV (Remote Operated Vehicle) is by using an experimental PMM (Planar Motion Mechanism) or CWC (Circular Water Channel); however, the use of these experimental infrastructures is costly. Therefore, it is of interest to obtain these coefficients in other ways, for example, by the use of simple experiments. The Free Decay Test is an ideal type of experiment, as it has a low cost and is simple to implement. In this paper, two different free decay tests were carried out, to which three different methods for obtaining coefficients were applied. They were compared with results obtained by CFD simulation to conduct a statistical analysis in order to determine their behaviours. It was possible to obtain values of the drag and added mass coefficients for the models analysed, where the values were obtained for an Underwater Drone Robot (UDrobot).

22 August 2018 in Sensors
Verified
Journal Article
Open access
PDF file
ABAlejandro Rodriguez Barroso
Alejandro Rodriguez Barroso
Roque SaltarenRoque Saltaren
Roque Saltaren
GPGERARDO PORTILLA
GERARDO PORTILLA
Juan S. CelyJuan S. Cely
Juan S. Cely
MAMarco Alexander Carpio Alemán
Marco Alexander Carpio Alemán
Redundancy in cable-driven parallel robots provides additional degrees of freedom that can be used to achieve different objectives. In this robot, this degree of freedom is used to act on a reconfigurable end effector with one degree of freedom. A compliant actuator actuated by one motor exerts force on both bodies of the platform. Due to the high tension that appears in this cable in comparison with the rest of the cables, an elastic model was developed for solving the kinestostatic and wrench analysis. A linear sensor was used in one branch of this cable mechanism to provide the needed intermediate values. The position of one link of the platform was fixed in order to focus this analysis on the relationship between the cables and the platform’s internal movement. Position values of the reconfigurable end effector were calculated and measured as well as the tension at different regions of the compliant actuator. The theoretical values were compared with dynamic simulations and real prototype results.

17 August 2019 in Sensors
Verified
Journal Article
Open access
PDF file
GPGERARDO PORTILLA
GERARDO PORTILLA
RSRoque Saltarén
Roque Saltarén
FEFrancisco Montero de Espinosa
Francisco Montero de Espinosa
ABAlejandro Rodriguez Barroso
Alejandro Rodriguez Barroso
Juan S. CelyJuan S. Cely
Juan S. Cely
Oz YakrangiOz Yakrangi
Oz Yakrangi
In this research, the dynamic walking of a legged robot in underwater environments is proposed. For this goal, the underwater zero moment point (Uzmp) is proposed in order to generate the trajectory of the centre of the mass of the robot. Also, the underwater zero moment point auxiliary (Uzmp aux.) is employed to stabilize the balance of the robot before it undergoes any external perturbations. The concept demonstration of a legged robot with hydraulic actuators is developed. Moreover, the control that was used is described and the hydrodynamic variables of the robot are determined. The results demonstrate the validity of the concepts that are proposed in this article, and the dynamic walking of the legged robot in an underwater environment is successfully demonstrated.

19 February 2021 in Electronics
Verified
Journal Article
Open access
PDF file
Oz YakrangiOz Yakrangi
Oz Yakrangi
Roque SaltarenRoque Saltaren
Roque Saltaren
Juan S. CelyJuan S. Cely
Juan S. Cely
ABAlejandro Rodriguez Barroso
Alejandro Rodriguez Barroso
Cecilia Elisabet Garcia CenaCecilia Elisabet Garcia Cena
Cecilia Elisabet Garcia Cena
ASAmir Shapiro
Amir Shapiro
The aim of this article is to present the fuzzy Petri net algorithm and its implementation on the Guide d’etude des modes de marche et d’arrêt (GEMMA) guide paradigm. Additionally, this article presents a brief description of the GEMMA guide paradigm, the fuzzy logic approach, the Petri nets theory, and fuzzy Petri nets. Each algorithm is intended for a specific set of transitions, depending on their essential conditions. All these algorithms generate intelligent and safe control of the GEMMA guide paradigm in order to have the best control system for the machine. Moreover, the algorithms are able to make the best decision automatically depending on the machine’s situation and condition, something that allows the machine to be placed in the appropriate mode for each situation. The results show that the different fuzzy Petri net algorithms were working properly for the GEMMA guide paradigm and provided a proper solution for the automation of production systems.

15 November 2022 in Sensors
Verified
Journal Article
Open access
PDF file
Juan S. CelyJuan S. Cely
Juan S. Cely
MBMIGUEL ÁNGEL PÉREZ BAYAS
MIGUEL ÁNGEL PÉREZ BAYAS
MAMarco Alexander Carpio Alemán
Marco Alexander Carpio Alemán
Cecilia Elisabet Garcia CenaCecilia Elisabet Garcia Cena
Cecilia Elisabet Garcia Cena
ASAvishai Sintov
Avishai Sintov
Roque SaltarenRoque Saltaren
Roque Saltaren
In underwater environments, ensuring people’s safety is complicated, with potentially life-threatening outcomes, especially when divers have to work in deeper conditions. To improve the available solutions for working with robots in this kind of environment, we propose the validation of a control strategy for robots when taking objects from the seabed. The control strategy proposed is based on acceleration feedback in the model of the system. Using this model, the reference values for position, velocity and acceleration are estimated, and then the position error signal can be computed. When the desired position is obtained, it is possible to then obtain the position error. The validation was carried out using three different objects: a ball, a bottle, and a plant. The experiment consisted of using this control strategy to take those objects, which the robot carried for a moment to validate the stabilisation control and reference following the control in terms of angle and depth. The robot was operated by a pilot from outside of the pool and was guided using a camera and sonar in a teleoperated way. As an advantage of this control strategy, the model upon which the robot is based is decoupled, allowing control of the robot for each uncoupled plane, this being the main finding of these tests. This demonstrates that the robot can be controlled by a control strategy based on a decoupled model, taking into account the hydrodynamic parameters of the robot.

2 August 2019 in Sensors
Verified
Journal Article
Open access
PDF file
ABAlejandro Rodriguez Barroso
Alejandro Rodriguez Barroso
Roque SaltarenRoque Saltaren
Roque Saltaren
GPGERARDO PORTILLA
GERARDO PORTILLA
Juan S. CelyJuan S. Cely
Juan S. Cely
Oz YakrangiOz Yakrangi
Oz Yakrangi
Cable-driven parallel robots with a redundant configuration have infinite solutions for their cable tension distribution to provide a specific wrench to the end-effector. Redundancy is commonly used to increase the workspace and stiffness or to achieve secondary objectives like energetic minimization or additional movements. This article presents a method based on energy distribution to handle the redundancy of cable-driven parallel robots. This method allows the deformation and tension of each link to be related to the total energy available in the parallel robot. The study of energy distribution expression allows deformation, tension, and position to be combined. It also defines the range of tension and deformation that cables can achieve without altering the wrench exerted on the end-effector. This range is used with a passive reconfigurable end-effector to control the position of two grippers attached to some cables which act as compliant actuators. The relationship between the actuators’ energy and their corresponding gripper positions is also provided. In this way, energy measurement from the actuators allows the grasping state to be sensed. The results are validated using multibody dynamic software.